Токарные инструменты Iscar (часть 1) 2026 - страница 640

FACE GROOVING DAXN LH HGHR/L-3 DAXX H OAH Integral Holders for Face Grooving and Turning DAXN-DAXX CDX HBH OAW OAL CDX WF CW B Right-hand shown Designation CW CDX DAXN(1) DAXX(2) WF H OAH B OAW OAL LH HBH MIID(3) HGHL 1212-12-3T6 3.00 6.00 12.0 16.0 11.00 12.0 19.00 12.0 15.70 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 1616-12-3T6 3.00 6.00 12.0 16.0 15.00 16.0 21.00 16.0 19.70 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 1616-16-3T6 3.00 6.00 16.0 25.0 15.00 16.0 21.00 16.0 18.80 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 2020-12-3T6 3.00 6.00 12.0 16.0 20.00 20.0 25.00 20.0 24.00 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 2020-16-3T6 3.00 6.00 16.0 25.0 20.00 20.0 25.00 20.0 24.00 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 2525-12-3T6 3.00 6.00 12.0 16.0 25.00 25.0 30.00 25.0 29.00 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHL 2525-16-3T6 3.00 6.00 16.0 25.0 25.00 25.0 30.00 25.0 29.00 120.00 19.0 - HGPL 3003Y SR 76-1400 T-20/3 HGHR 1010-12-3T6 3.00 6.00 12.0 16.0 9.50 10.0 19.00 10.0 13.70 120.00 19.0 2.0 GRIP 3003Y SR 76-1400 T-20/3 HGHR 1010-16-3T6 3.00 6.00 16.0 25.0 9.50 10.0 19.00 10.0 12.80 120.00 19.0 2.0 GRIP 3003Y SR 76-1400 T-20/3 HGHR 1212-12-3T6 3.00 6.00 12.0 16.0 11.00 12.0 19.00 12.0 15.70 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 1212-16-3T6 3.00 6.00 16.0 25.0 11.00 12.0 19.00 12.0 14.80 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 1616-12-3T6 3.00 6.00 12.0 16.0 15.00 16.0 21.00 16.0 19.70 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 1616-16-3T6 3.00 6.00 16.0 25.0 15.00 16.0 21.00 16.0 18.80 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 2020-12-3T6 3.00 6.00 12.0 16.0 20.00 20.0 25.00 20.0 24.00 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 2020-16-3T6 3.00 6.00 16.0 25.0 20.00 20.0 25.00 20.0 24.00 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 2525-12-3T6 3.00 6.00 12.0 16.0 25.00 25.0 30.00 25.0 29.00 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 HGHR 2525-16-3T6 3.00 6.00 16.0 25.0 25.00 25.0 30.00 25.0 29.00 120.00 19.0 - GRIP 3003Y SR 76-1400 T-20/3 • HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 676-688 (1) Minimum penetration diameter (2) Maximum penetration diameter (3) Master insert identification For inserts, see pages: GRIPA (296) • GRIPA (full radius) (296) • GRIP (294) • GRIP (full radius) (295) • HGN-C (549) • HGN-J (550) • HGN-UT (551) • HGPL (658) Groove can be widened with no limitation toward or away d from the center except for the following tools: HGHR/L...-12-3T6 D d Limitation of widening toward center 12�0 4�0 depends on the major diameter (D) as 13�0 1�0 per chart� D 13�5 0 LH DAXN HFHR/L-3T CDX HF OAH DAXX HFHR/L --3T12 H Integral Holders for Facing WF2 CW DAXN-DAXX CDX WF B OAL Right-hand shown Designation CW CDX DAXN(2) DAXX(3) WF HF H OAH B OAL WF2 LH MIID(4) HFHR/L 20-25-3T12 3.00 12.00 25.0 30.0 20.50 20.0 20.0 28.00 20.0 140.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 20-30-3T12 3.00 12.00 30.0 38.0 20.50 20.0 20.0 29.00 20.0 140.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 20-38-3T12 3.00 12.00 38.0 48.0 20.50 20.0 20.0 30.00 20.0 140.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 20-48-3T12 3.00 12.00 48.0 60.0 20.50 20.0 20.0 30.00 20.0 140.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-25-3T12 3.00 12.00 25.0 30.0 25.50 25.0 25.0 33.00 25.0 150.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-30-3T12 3.00 12.00 30.0 38.0 25.50 25.0 25.0 34.00 25.0 150.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-38-3T12 3.00 12.00 38.0 48.0 25.50 25.0 25.0 35.00 25.0 150.00 5.3 38.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 20-60-3T22 (1) 3.00 22.00 60.0 75.0 20.50 20.0 20.0 31.00 20.0 140.00 - 40.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-48-3T22 (1) 3.00 22.00 48.0 60.0 25.50 25.0 25.0 36.00 25.0 150.00 - 40.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-60-3T22 (1) 3.00 22.00 60.0 75.0 25.50 25.0 25.0 36.00 25.0 150.00 - 40.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 20-75-3T25 (1) 3.00 25.00 75.0 100.0 20.50 20.0 20.0 31.00 20.0 140.00 - 43.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 HFHR/L 25-75-3T25 (1) 3.00 25.00 75.0 100.0 25.50 25.0 25.0 36.00 25.0 150.00 - 43.0 HFPL 3003 SR M6X16 DIN912 HW 5.0 • For user guide, see pages 676-688 (1) For deep face grooving only. (2) Minimum penetration diameter (3) Maximum penetration diameter (4) Master insert identification For inserts, see pages: HFPR/L (656) • HFPR/L (full radius) (656) Penetration Range No limitation for widening groove toward or away from center, d except for the following tools: HFHR/L-#-25-3T12 HFHR/L-#-25-4T12 HFHR/L-#-29-4T12 D d D d D d Limitation of widening toward 25 5 25 1 29 1 center (d) depends on the major D 26 2 ≥26 0 ≥46 0 diameter (D) as per chart ≥27 0 638 ISCAR