Токарные инструменты Iscar (часть 1) 2026 - страница 416

TOOLS FOR MINIATURE PARTS GAN HF Workpiece 4 41 SCIR/L-41-N/R/L 8.5 Grooving and Parting Inserts Tc CDX 15° Tc SCIR 41-...R15K.. CDX CW Sharp corner x 2 SCIR 41-...N-K00 Right-hand shown Recommended Dimensions Machining Data IC1008 f groove Designation CW CWTOL(1) GAN HF(2) CDX Tc (mm/rev) SCIL 41-100L15K00 1.00 0.020 0.0 0.2 6.00 11.0 • 0.02-0.04 SCIR/L 41-100N-K00 1.00 0.020 0.0 0.1 6.15 11.0 • 0.03-0.05 SCIR 41-100R15K00 1.00 0.020 0.0 0.2 6.00 11.0 • 0.02-0.04 SCIL 41-150L15K00 1.50 0.020 0.0 0.2 8.00 11.0 • 0.03-0.06 SCIR/L 41-150N-K00 1.50 0.020 0.0 0.1 8.15 11.0 • 0.03-0.07 SCIR 41-150R15K00 1.50 0.020 0.0 0.2 8.00 11.0 • 0.03-0.06 SCIL 41-150L15K7 1.50 0.020 7.0 0.5 8.00 11.0 • 0.03-0.06 SCIR 41-150R15K7 1.50 0.020 7.0 0.5 8.00 11.0 • 0.03-0.06 SCIL 41-200L15K00 2.00 0.020 0.0 0.2 10.00 11.0 • 0.03-0.07 SCIR/L 41-200N-K00 2.00 0.020 0.0 0.1 11.00 11.0 • 0.03-0.09 SCIR 41-200R15K00 2.00 0.020 0.0 0.2 10.00 11.0 • 0.03-0.07 SCIL 41-200L15K7 2.00 0.020 7.0 0.5 10.00 11.0 • 0.03-0.07 SCIR 41-200R15K7 2.00 0.020 7.0 0.5 10.00 11.0 • 0.03-0.07 SCIL 41-250L15K00 2.50 0.020 0.0 0.2 10.00 11.0 • 0.03-0.07 SCIR/L 41-250N-K00 2.50 0.020 0.0 0.1 11.00 11.0 • 0.03-0.09 SCIR 41-250R15K00 2.50 0.020 0.0 0.2 10.00 11.0 • 0.03-0.07 SCIL 41-250L15K7 2.50 0.020 7.0 0.5 10.00 11.0 • 0.03-0.07 SCIR 41-250R15K7 2.50 0.020 7.0 0.5 10.00 11.0 • 0.03-0.07 SCIL 41-300L15K00 3.00 0.020 0.0 0.2 10.00 11.0 • 0.03-0.08 SCIR/L 41-300N-K00 3.00 0.020 0.0 0.1 11.00 11.0 • 0.03-0.10 SCIR 41-300R15K00 3.00 0.020 0.0 0.2 10.00 11.0 • 0.03-0.08 • For cutting speed recommendations and user guide, see pages 475-492 (1) Cutting width tolerance (+/-) (2) Cutting edge below center For tools, see pages: SCHR/L-41BF (412) Workpiece 9° HF 4 41 SCIR/L-41-NP 8.5 Grooving, Turning and CDX Parting Inserts Tc CW 7° Tc CDX RE x 2 Dimensions Recommended Machining Data ap f turn f groove IC1008 Designation CW CWTOL(1) RE RETOL(2) HF(3) CDX Tc (mm) (mm/rev) (mm/rev) SCIR/L 41-150NP08 1.50 0.020 0.08 0.020 0.2 8.00 11.0 • 0.10-1.80 0.02-0.10 0.02-0.07 SCIR/L 41-200NP08 2.00 0.020 0.08 0.020 0.2 8.00 11.0 • 0.10-2.50 0.02-0.15 0.02-0.09 SCIR/L 41-250NP08 2.50 0.020 0.08 0.020 0.2 10.00 11.0 • 0.10-3.00 0.02-0.17 0.02-0.11 SCIR/L 41-300NP08 3.00 0.020 0.08 0.020 0.2 10.00 11.0 • 0.10-4.00 0.02-0.20 0.02-0.12 • When turning to the opposite side of chipformer, maximum D.O.C. is 0.5 mm (1) Cutting width tolerance (+/-) (2) Corner radius tolerance (+/-) (3) Cutting edge below center For tools, see pages: SCHR/L-41BF (412) 414 ISCAR