Каталог Sumitomo фрезы со сменными пластинами

WRXSEC-WaveRepeater

Cutting Conditions: Depth of Cut 30mm, Cutting Width 8mm

Grades

Work ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000

Work Material	Hardness	Per Edge Feed Rate	(mm/t)
			z

		(HB)		0.1 0.15 0.2		0.1 0.15 0.2 0.1 0.15 0.2			0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2
									(m/min) Cutting Speed
									c
	Steel, Carbon Steel S15C	125	G	280 260 240 260 240 220 240 220 200
		S45C 190	G	200 180 160 180 160 140 180 160 140
		S45C Hardened 250	G	180 120 140 160 140 120 150 130 110
		S75C 270	G	160 140 120 150 130 110 130 110 110
		S75C Hardened 300	G	100	80 70	60 70 90 70	60	50
P	Low Alloy Steel SCM, SNCM	180	G	200 180 160 180 160 150 160 150 130
		SCM, SNCM Hardened 275	G	130 110	90 120 100 90 100		90	80
		SCM, SNCM Hardened 300	G	120 100	80 100	80 90 90	80	60
		SCM, SNCM Hardened 350	G	90	80 60	60 70 80 70	60	40
	High Alloy Steel SKD, SKT, SKH	200	G	180 170 160 170 160 130 150 140 120
		SKD, SKT, SKH Hardened 325	G	100	80 60	50 60 80 60	50	30
	Stainless Steel SUS430 and Others (Martensitic/Ferritic)	200	E						170 150 120 140 130 110
M		SUS403 and Others (Martensitic, Hardened) 240	E						90 140 120 100 120 100
		SUS304, SUS316 (Austenitic) 180	E						180 160 140 160 140 130
	Cast Iron		G						240 220 200 220 200 180
K
	Ductile Cast Iron		G						160 140 120 140 120 100
S	Exotic Alloy		E						25 45 35 50
	Aluminum Alloy Si<12.6%		S						1000 750 500
N
	Si>12.6%		S						250 200 170

The recommended cutting conditions may not be practical under certain operating conditions (i.e., machine, work shape, clamping system. The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth, and other factors. Note

: Face

Cutting Conditions	Depth of Cut 50mm, Cutting Width 10mm		Milling
			Shoulder
		Grades	Milling

Work ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000 High Feed

Work Material	Hardness	Per Edge Feed Rate	(mm/t)
			z

	(HB)		0.1 0.15 0.2	0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 Radius
				(m/min) Cutting Speed
				c Multi-
Steel, Carbon Steel S15C	125	G	320 300 280 300 280 260 280 260 240	Purpose
	S45C 190	G	240 220 200 220 200 180 200 180 160	R/
				Profiling
	S45C Hardened 250	G	200 180 160 180 160 140 160 140 120
				Groove/
	S75C 270	G	160 140 120 150 130 110 130 110 110	T-Slot
	S75C Hardened 300	G	120 100 80	50 60 80 60 80 100
				Chamfering
P Low Alloy Steel SCM, SNCM	180	G	220 200 180 200 180 170 180 170 150
	SCM, SNCM Hardened 275	G	140 120 100 130 110 100 110 100	80 Aluminum/
				Light Alloys
	SCM, SNCM Hardened 300	G	130 110 90	60 100 80 80 90 110
				High-Speed
	SCM, SNCM Hardened 350	G	100	40 60 70 60 70 90 60 80 Cast Iron
High Alloy Steel SKD, SKT, SKH	200	G	200 180 160 180 160 140 160 140 120
	SKD, SKT, SKH Hardened 325	G	100	30 50 60 50 60 80 60 80
Stainless Steel SUS430 and Others (Martensitic/Ferritic)	200	E		170 150 130 140 130 110
M	SUS403 and Others (Martensitic, Hardened) 240	E		90 140 120 100 120 100
	SUS304, SUS316 (Austenitic) 180	E		180 160 140 160 140 130
Cast Iron		G		240 220 200 220 200 180
K
Ductile Cast Iron		G		160 140 120 140 120 100
S Exotic Alloy		E		25 45 30 50
Aluminum Alloy Si<12.6%		S		1000 750 500
N
Si>12.6%		S		250 200 170

The recommended cutting conditions may not be practical under certain operating conditions (i.e., machine, work shape, clamping system. The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth, and other factors.