Каталог Sumitomo фрезы со сменными пластинами - страница 75

Предыдущая страница Следующая страница

Навигация

Expansion Type

■ Recommended Cutting Conditions Cutting Width ae=1mm

WEX1000 Type

Depth of Cut □ a =4mm

Tool: WEX1012E Insert: AXT0602 Typep
Cutting Conditions: Depth of Cut 4mm, Cutting Width 1mm, Dry
Grades

Work ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000

Work MaterialHardnessFeed fz (mm/t)
(HB)0.08 0.12 0.16 0.08 0.12 0.16 0.08 0.12 0.16 0.10 0.15 0.20 0.10 0.15 0.20 0.08 0.10 0.12 0.08 0.10 0.12 0.05 0.10 0.15
Cutting Speed vc (m/min)
Steel, Carbon Steel S15C125G260 240 220 240 220 200 220 200 180
S45C190G200 180 160 180 160 140 180 160 140
S45C Hardened250G180 120 140 160 140 120 150 130 110
S75C270G160 140 120 150 130 110 130 110 110
S75C Hardened300G100 8070 90 70 60706050
PLow Alloy SteelSCM、SNCM180G200 180 160 180 160 150 160 150 130
SCM、SNCM Hardened 275G130 110 90 120 100 90 100 9080
SCM、SNCM Hardened 300G120 100 80 100 9080908060
SCM、SNCM Hardened 350G9070 80 60 80 60706040
High Alloy SteelSKD、SKT、SKH200G180 170 160 170 160 130 150 140 120
SKD、SKT、SKH Hardened325G100 8060 80 60 50605030
Stainless SteelSUS430 and Others (Martensitic/Ferritic)200E170 150 120 140 130 110
MSUS403 and Others (Martensitic, Hardened) 240E140 120 100 120 100 90
SUS304、SUS316(Austenitic)180E180 160 140 160 140 130
Cast IronG240 220 200 220 200 180
K
Ductile Cast IronG160 140 120 140 120 100
SExotic AlloyE25 45 35 50
Aluminum Alloy, Si ≤ 12.6%S800 600 400
NAluminum Alloy, Si > 12.6%S240 200 160
Copper AlloyS330 300 270

D The recommended cutting conditions may not be practical under certain operating conditions (i.e., machine, work shape, clamping system). D For groove milling, adjust feed rate to around 70% of the above values. The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth, and other factors. Note

H

WEX2000 Type

Cutting Width a e=12.5mm

Tool: WEX2025E Insert: AX□T1235 Type

Depth of Cut a p=3mm Cutting Conditions: Depth of Cut 3mm, Cutting Width 12.5mm, Dry Face Grades Milling

WorkACP100ACP200ACP300ACK200ACK300ACM200ACM300DL1000Shoulder
Milling

Work Material Hardness Feed f (mm/t)

z (HB) High Feed 0.08 0.15 0.20 0.08 0.15 0.20 0.08 0.15 0.20 0.08 0.15 0.20 0.08 0.15 0.20 0.08 0.15 0.20 0.08 0.15 0.20 0.05 0.15 0.22 Cutting Speed vc (m/min)

Radius

Steel, Carbon Steel S15C125G380 350 330 350 330 315 330 315 295
S45C190G285 255 235 255 235 220 235 220 200Multi-
Purpose
S45C Hardened250G235 210 190 210 190 170 190 170 150
R/
S75C270G190 162 143 171 152 133 152 133 115Profiling
S75C Hardened300G145 11555 75 95 75 95 95 115 Groove/
P Low Alloy SteelSCM、SNCM180G265 235 220 235 220 200 220 200 180T-Slot
SCM、SNCM HardenedG
275170 145 125 150 130 115 130 11595 Chamfering
SCM、SNCM HardenedG75 95 95 115
300150 125 105 135 115
、Aluminum/
SCM SNCM Hardened 350G12545 65 85 65 85 75 105 95 Light Alloys
High Alloy SteelSKD、SKT、SKH200G235 210 190 210 190 170 190 170 150
High-Speed
SKD、SKT、SKH Hardened325G12535 55 75 55 75 95 75 95 Cast Iron
Stainless SteelSUS430 and Others (Martensitic/Ferritic)200E175 155 125 155 140 110
MSUS403 and Others (Martensitic, Hardened)240EH160 140 110 145 125 100
SUS304、SUS316(Austenitic)180E190 170 140 170 150 125
Cast IronG285 255 235 255 235 220
K
Ductile Cast IronG190 160 140 160 140 125
Exotic Alloy300E35 45 40 50
S
(Heat Resistant Alloy, Super Alloy, Ti Alloy, etc.)330E20 30 25 35
Aluminum Alloy, Si ≤ 12.6%S1000 750 500
N Aluminum Alloy, Si > 12.6%S250 200 170
Copper AlloyS350 330 300

D The recommended cutting conditions may not be practical under certain operating conditions (i.e., machine, work shape, clamping system). D For groove milling, adjust feed rate to around 70% of the above values. The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth, and other factors.