Каталог Sumitomo фрезы со сменными пластинами - страница 8

Modular Tool Selection Guide G: Optimal S: Good H: Unsuitable Blank: Not recommended Work Material Application H Shank Diameter (mm) P M K N S Application Type Cast Iron/Ductile Cast Iron Non-Ferrous Metal Hardened Steel 45 to 55 HRC Cutting Edge Angle Diameter Description Series Insert Cat. Rake Angle General Steel/Carbon Steel/Alloy Steel Finishing Face Milling Ti Alloy/Heat Resistant Alloy Tempered Steel/Die Steel Ref. Page Shoulder Milling Profile Finishing and (mm) No. and Aluminum Alloy Stainless Steel Max. Depth of Cut Diagram Chamfering Slot Milling (mm) Ramping Copying Cutting Edge Angle High Feed General Purpose Boring Radial Axial SOMT080304PZER-G WFX-M Modular RE ø20 ø18 6mm 90° to to WFX08000M 12° -6ﾟ S G S G G G G G G S H150 8.0 ø40 ø32 Shoulder Milling 8.0 →H150 (3000 Type) ø16 ø15 WEX-M Modular AXMT170504PEER-G 14ﾟ 10ﾟ 10mm 90° to to WEX2000M to to ø40 ø32 25ﾟ 18ﾟ S G G G G G G G G G G H151 ø25 ø23 10.2 16ﾟ 8ﾟ 14mm 90° to to WEX3000M RE 17.54 to to ø40 ø32 24ﾟ 15ﾟ →H151 (12000 Type) ø25 ø23 WFXH-M SOMT120308PDER 1.5mm 15° to to WFXH08000M 6ﾟ -6ﾟ ø32 ø32 G G G G G G G S H152 12.7 ø28 High Feed Cutting 2.5mm 15° ø40 to WFXH12000M 6ﾟ -6ﾟ ø32 12.7 →H152 (8000 Type) ø16 ø15 MSX-M Modular WDMT0804ZDTR 1.0mm 20° to to MSX06000M ø25 ø25 ø25 ø23 IC -3ﾟ 1.5mm 20° to to MSX08000M 8ﾟ to G S S G G G G S H153 H 2.0mm ø35 ø32 ø32 ø28 RE -6ﾟ 20° to to MSX12000M Cutters Milling ø40 ø32 →H153 (10000 Type) ø20 ø18 RSX-M Modular RDET10T3M0EN-G 4mm to to n RSX08000M 10° -8ﾟ ø32 ø32 Expansio Face Milling ø25 ø23 RSX10000M -5ﾟ 5mm to to 10° to G S G G G G H154 IC Shoulder RSXF10000M Milling ø32 ø32 -8ﾟ Radius Milling High Feed ø32 ø28 RSX12000M IC 6mm to to 10° -5ﾟ Radius ø40 ø32 →H154 RSXF12000M (10000 Type) Multi- ø20 ø18 WRCX-M Modular QPMT10T335PPEN Purpose 4mm to to WRCX08000M R/ ø25 ø25 RE Profiling ø25 ø23 IC Groove/ T-Slot 5mm to to WRCX10000M -3ﾟ 0° G S G G G G G G G S S H155 ø32 ø32 Chamfering IC ø28 90 Aluminum/ 6mm ø40 to WRCX12000M Light Alloys ø32 →H155 High-Speed (8000 Type) Cast Iron ø15 WFXC-M SOMT080308PZER-G ø16 to Chamfering WFXC08000M RE 0° 0° ø16 45° G G G G G G G S H156 8.0 ø25 ø23 to to WFXC12000M 0° 0° ø32 ø32 →H156 8.0 (*) Shank diameters in the above table are the sizes of corresponding arbors. Refer to H149 for details. H8