Общий каталог Tungaloy 2020 - 2021 - страница 989

Предыдущая страница Следующая страница

Навигация

STANDARD CUTTING CONDITIONS TPW / E P W13 type

ISOWorkpiece materialGradeCutting speed Vc (m/min)(Depth FeeRoug of cut: A d per toothing PMX ≥ 1.0 h:fz (mmmm) /t)Ligh (Depth Feet cutting of cut: A d per tooto finishi PMX ≥ 1. th:fz (mmng 0 mm) /t)nsert
MJMLMSAJMJMLMSAJI
AH3135 (First choice)100 - 2700.05 - 0.250.05 - 0.2--0.05 - 0.2 0.05 - 0.18--der
Mild steels Low carbon steelsT3225 (Wear resistance)150 - 3000.05 - 0.25---0.05 - 0.2---Toolhol
< 180HBAH130 (Fracture resistance)80 - 1800.05 - 0.25-0.05 - 0.2-0.05 - 0.2-0.05 - 0.18-Ext.
NS740 (Surface fi nish)100 - 3000.05 - 0.15---0.05 - 0.12---older
AH3135 (First choice)100 - 2300.05 - 0.20.05 - 0.15--0.05 - 0.18 0.05 - 0.12--t. Toolh
Carbon steels All lT3225 (Wear resistance)150 - 2800.05 - 0.2---0.05 - 0.18---In
oy stees < 300HBAH130 (Fracture resistance)80 - 1500.05 - 0.2---0.05 - 0.18---adin
NS740 (Surface fi nish)100 - 2300.05 - 0.15---0.05 - 0.12---Thre
Die steelsAH3135 (First choice)100 - 1800.05 - 0.150.05 - 0.12--0.05 - 0.120.05 - 0.1--ng
< 30HRCT3225 (Wear resistance)100 - 1800.05 - 0.15---0.05 - 0.12---roovi
Stainless steelsAH130 / AH3135 (First choice)80 - 2000.05 - 0.2-0.05 - 0.18-0.05 - 0.18-0.05 - 0.15-G l
< 50HBAH120 (Wear resistance)150 - 2500.05 - 0.20.05 - 0.15--0.05 - 0.18 0.05 - 0.12--re too
Grey cast ironsT1215 (First choice)100 - 2500.05 - 0.2---0.05 - 0.18---iniatu
Ductile cast ironsAH120 (Fracture resistance)100 - 2500.05 - 0.20.05 - 0.15--0.05 - 0.18 0.05 - 0.12--M er
Aluminium alloys Si < 13 %DS1100 / KS05F (First choice)300 - 1000---0.05 - 0.2---0.05 - 0.2g cutt
Aluminium alloys Si ≥ 13 %DS1100 / KS05F (First choice)80 - 300---0.05 - 0.2---0.05 - 0.2Millin
Copper alloysDS1100 / KS05F (First choice)200 - 500---0.05 - 0.2---0.05 - 0.2l

DS1100 / KS05F Notes: When machining at large depth of cut or large cutting width, Vc and fz should be reduced. When machining mild steel, carbon steel or alloy steel in wet conditions the T3130 is As a rule, dry machining (including air blow) is recommended. But, for excessive chip recommended. In this case, Vc and fz should be reduced. welding, such as when machining stainless steels, use a water soluble cutting fl uid. In this TPW13 type can not be used for ramping, plunging and drilling. case, use AH140 and set the cutting speed to Vc ) 100 m/min.

I

J

K

L

M