Общий каталог Tungaloy 2020 - 2021

Брошюра Tungaloy новая продукция

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy зубофрезерование

Каталог Tungaloy глубокое сверление 2

ISO	Workpiece material	Priority	Chip breaker	Cutting speed Vc (m/min)	ø12 - ø13.99	ø14 - ø18 feed:f	ø18.01 - ø28 (mm/rev)	ø28.01 - ø40
	Low carbon steel (C < 0.3) SS400 SM490 S25C t	Lower feed	NDL	50 - 100	-	0.03 - 0.1	0.03 - 0.1	-
	, , , ec. E275A, E355D, C25, etc.	First recommendation	NDJ/G	80 - 140	0.05 - 0.1	0.05 - 0.1	0.05 - 0.1	0.1 - 0.2
	Carbon steel (C > 0.3)	Lower feed	NDL	50 - 100	-	0.03 - 0.1	0.03 - 0.12	-
	S45C, S55C, etc. C45, C55, etc.	First recommendation	NDJ/G	80 - 140	0.05 - 0.16	0.05 - 0.16	0.05 - 0.2	0.1 - 0.2
	Low alloy steel (C < 0.3)	Lower feed	NDL	50 - 100	-	0.03 - 0.1	0.03 - 0.1	-
	SCM415, etc. 18CrMo4, etc.	First recommendation	NDJ/G	80 - 140	0.05 - 0.1	0.05 - 0.1	0.05 - 0.1	0.1 - 0.2
	Alloy steel (C > 0.3) SCM440 SC420 t	Lower feed	NDL	50 - 100	-	0.03 - 0.1	0.03 - 0.12	-
	, r, ec. 42CrMo4, 20Cr4, etc.	First recommendation	NDJ/G	80 - 120	0.05 - 0.16	0.05 - 0.16	0.05 - 0.2	0.1 - 0.2
	Stainless steel (Austenitic) SUS304 SUS316 t	Lower feed	NDL	50 - 100	-	0.03 - 0.06	0.03 - 0.06	-
	, , ec. X5CrNi18-9, X5CrNiMo17-12-3, etc.	First recommendation	NDJ/G	60 - 100	0.05 - 0.1	0.05 - 0.1	0.05 - 0.1	0.1 - 0.15
	Stainless steel (Martensitic, Ferritic)	Lower feed	NDL	50 - 100	-	0.03 - 0.06	0.03 - 0.06	-
	SUS430, SUS416, etc. X6Cr17, X12CrS13, etc.	First recommendation	NDJ/G	60 - 100	0.05 - 0.1	0.05 - 0.1	0.05 - 0.1	0.1 - 0.15
	Stainless steel (Precipitation hardening)	Lower feed	NDL	50 - 100	-	0.03 - 0.06	0.03 - 0.06	-
	SUS630, etc. X5CrNiCuNb16-4, etc.	First recommendation	NDJ/G	60 - 100	0.05 - 0.1	0.05 - 0.1	0.05 - 0.1	0.1 - 0.15
	Grey cast iron FC250 t	Lower feed	NDL	50 - 100	-	0.03 - 0.15	0.05 - 0.18	-
	, ec. 250, etc.	First recommendation	NDJ/G	80 - 140	0.05 - 0.25	0.05 - 0.25	0.05 - 0.3	0.1 - 0.3
	Ductile cast iron	Lower feed	NDL	50 - 100	-	0.03 - 0.15	0.05 - 0.18	-
	FCD700, etc. 600-3, etc.	First recommendation	NDJ/G	80 - 140	0.05 - 0.25	0.05 - 0.25	0.05 - 0.3	0.1 - 0.3
		Lower feed	NDL	80 - 160	-	0.03 - 0.15	0.03 - 0.15	-
	Aluminium alloys	First recommendation	NDJ/G	100 - 200	0.05 - 0.2	0.05 - 0.2	0.05 - 0.2	0.1 - 0.25
	Heat resistant alloys	Lower feed	NDL	20 - 50	-	0.03 - 0.06	0.03 - 0.08	-
	Inconel 718, etc.	First recommendation	NDJ/G	20 - 50	0.04 - 0.08	0.04 - 0.08	0.04 - 0.1	0.06 - 0.13
	Titanium alloys	Lower feed	NDL	30 - 60	-	0.03 - 0.1	0.03 - 0.12	-
	Ti-6Al-4V, etc.	First recommendation	NDJ/G	30 - 60	0.05 - 0.13	0.05 - 0.13	0.05 - 0.15	0.1 - 0.18
	Hardened steel	Lower feed	NDL	40 - 100	-	0.03 - 0.08	0.03 - 0.08	-
	�40HRC	First recommendation	NDJ/G	50 - 100	0.04 - 0.08	0.04 - 0.08	0.04 - 0.1	0.06 - 0.13

	* 40HRC	First recommendation	NDJ/G	50 - 100	0.04 - 0.08	0.04 - 0.08	0.04 - 0.1	0.06 - 0.13	G
APPLICATION RANGE
Feed

f	0.03 - 0.05	0.03 - 0.05	0.1 - 0.3
(mm/rev)

OK Cross hole OK OK H

Inclined exit Boring drilling Application I 16 mm or less

(for standard drill)

Note 1) When drilling cross holes or exiting the inclined surface, make sure the guide-pads are suitable. J Note 2) A pilot hole is needed prior to a boring operation. ap ≥ 1 mm is recommended for boring operations.

SHAPES O F THE HOLE BOTTOM

DC 12 - 13.99	LOGT06 Insert	PL 1.8 Maximum difference	LOGT06.. DC	.	TOHT09... - TOHT12... TOHT07..., 08... DC DC
14 - 15.99	TOHT07	2
16 - 18	TOHT08	2.2
18.01 - 20	TOHT09	3		L	PL
20.01 - 21.99	TOHT10	3.2		P	PL
22 - 25	TOHT11	3.4
25.01 - 28	TOHT12	3.7
DC	Central	Intermediate Insert	Peripheral	PL Maximum difference	FBM...
28.01 - 29	FBM06504LG-C	FBM05503RG-I	FBH06003RG-P	2.6
29.01 - 29.99	FBM06504LG-C	FBM05503RG-I	FBH06003RG-P	2.6	DC
30 - 31	FBM06504LG-C	FBM06504RG-I	FBH07504RG-P	2.9
31.01 - 32	FBM06504LG-C	FBM06504RG-I	FBH07504RG-P	3
32.01 - 33	FBM06504LG-C	FBM06504RG-I	FBH07504RG-P	3.1
33.01 - 34	FBM06504LG-C	FBM06504RG-I	FBH07504RG-P	3
34.01 - 35	FBM06504LG-C	FBM06504RG-I	FBH07504RG-P	3.1
35.01 - 36	FBM08004LG-C	FBM06504RG-I	FBH07504RG-P	3.1	PL
36.01 - 37	FBM08004LG-C	FBM06504RG-I	FBH07504RG-P	3
37.01 - 38	FBM08004LG-C	FBM06504RG-I	FBH07504RG-P	3.1
38.01 - 39	FBM08004LG-C	FBM06504RG-I	FBH09004RG-P	3.4
39.01 - 40	FBM08004LG-C	FBM06504RG-I	FBH09004RG-P	3.3

Общий каталог Tungaloy 2020 - 2021 - страница 1335

Навигация

(for standard drill)

SHAPES O F THE HOLE BOTTOM

Общий каталог Tungaloy 2020 - 2021 - страница 1335

Навигация

(for standard drill)

SHAPES O F THE HOLE BOTTOM

Отправьте заявку

На подбор необходимой оснастки и оборудования