2-effective DrillIndexable DrillDeep Hole Drill BD A P P L I C AT I O N RANGE *In case of Interrupted cutting, feed should be decreased. Feedf (mm/rev) Refer to J060 - J061 page 0.05 0.05 0.05 OKPlane surface OKSlant surface OKCross hole OKPlunging Application range Feedf (mm/rev) 0.1 0.05 Disapprove Disapprove OKBoring OKRound surface Stacked plates Back boring Application range TDXCF chamfering tool Chamfering tool for Tu n g D r i l l Tw i s t e d and Tu n g S i x - D r i l l Max. drilling depth LF DCONMS Designation DCONMS BD LF Application drill Max. drilling depthL/D = 2L/D = 3L/D = 4 TDXCF200L25 19.1 49 25 TDS200*25-* 15.5 35.5 62.5 TDXCF210L25 20.1 49 25 TDS205*25-* 16.5 37 64.6 TDXCF210L25 20.1 49 25 TDS209F25-3 - 38.5 - TDXCF210L25 20.1 49 25 TDS210*25-* 17.5 38.5 66.5 TDXCF220L25 21.1 49 25 TDS215*25-* 18.5 40 68.6 TDXCF220L25 21.1 49 25 TDS220*25-* 19.5 41.5 70.5 TDXCF230L25 22.1 49 25 TDS225*25-* 20.5 43 72.6 TDXCF230L25 22.1 49 25 TDS230*25-* 21.5 44.5 74.5 TDXCF240L25 23.1 49 25 TDS235*25-* 22.5 46 76.6 TDXCF240L25 23.1 49 25 TDS239F25-3 - 47.5 - TDXCF240L25 23.1 49 25 TDS240*25-* 23.5 47.5 78.5 TDXCF250L25 23.95 49 25 TDS245*25-* 24.5 49 80.6 TDXCF250L25 23.95 49 25 TDS250*25-* 25.5 50.5 82.5 TDXCF260L30 24.95 64 30 TDS255*25-* 21.5 47 79.6 TDXCF260L30 24.95 64 30 TDS260*25-* 22.5 48.5 81.5 TDXCF270L30 25.9 64 30 TDS264F32-3 - 50 - TDXCF270L30 25.9 64 30 TDS265F32-3 - 50 - TDXCF270L30 25.9 64 30 TDS270*32-* 24.5 51.5 85.5 TDXCF280L30 26.9 64 30 TDS280*32-* 26.5 54.5 89.5 TDXCF290L30 27.9 64 30 TDS290*32-* 28.5 57.5 93.5 TDXCF300L30 28.9 64 30 TDS300*32-* 30.5 60.5 97.5 TDXCF310L30 29.9 64 30 TDS310*32-* 32.5 63.5 101.5 TDXCF320L30 30.9 64 30 TDS320*32-* 34.5 66.5 105.5 SPARE PARTS Designation Screw for insert Screw for ring Wrench for insert Wrench for ring TDXCF130 - 230 CSPB-4S CM6X16 IP-15D P-5 TDXCF260 - 540 CSPB-4S CM8X1.25X20-A IP-15D P-6 Recommended clamping torque (N∙m): CSPB-4S = 3.5 J062 www.tungaloy.com