Общий каталог Tungaloy 2020 - 2021 - страница 1033

Брошюра Tungaloy новая продукция

Брошюра Tungaloy новая продукция

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy зубофрезерование

Каталог Tungaloy зубофрезерование

Каталог Tungaloy глубокое сверление 2

Каталог Tungaloy глубокое сверление 2

ISO	Workpiece materials	Hardness	Priority	Grades	Max. depth of cut (mm)	Cutting speed Vc (m/min)	D8	D10	D12 Feed	D16 per to	D20 oth:f	D25 z(mm	D30 /t)	D32
	Low carbon steel,	85 - 180 HB	First choice	AH725	≤ 0.04D	180 - 260	0.15	0.2	0.2	0.25	0.25	0.3	0.35	0.35
	alloy steel	85 - 180 HB	Wear resistance	AH710	≤ 0.04D	180 - 260	0.15	0.2	0.2	0.25	0.25	0.3	0.35	0.35
	High carbon steel,	180 - 280 HB	First choice	AH725	≤ 0.03D	150 - 230	0.15	0.2	0.2	0.25	0.25	0.3	0.35	0.35
	alloy steel	180 - 280 HB	Wear resistance	AH710	≤ 0.03D	180 - 230	0.15	0.2	0.2	0.25	0.25	0.3	0.35	0.35
	Prehardened steel	40 - 48 HRC	First choice	AH710	≤ 0.03D	180 - 300	0.15	0.15	0.2	0.2	0.25	0.25	0.3	0.3
	Die & mold tool steel	40 - 48 HRC	Fracture resistance	AH725	≤ 0.03D	180 - 300	0.15	0.15	0.2	0.2	0.25	0.25	0.3	0.3
	Stainless steel	135 - 200 HB	First choice	AH725	≤ 0.03D	100 - 250	0.1	0.15	0.2	0.2	0.25	0.25	0.3	0.3
		150 - 240 HB	First choice	AH710	≤ 0.04D	90 - 350	0.2	0.2	0.25	0.3	0.3	0.35	0.4	0.4
	Cast iron	150 - 240 HB	Fracture resistance	AH725	≤ 0.04D	90 - 350	0.2	0.2	0.25	0.3	0.3	0.35	0.4	0.4
	Aluminium	-	First choice	AH725	≤ 0.03D	200 - 400	0.25	0.25	0.35	0.35	0.35	0.4	0.4	0.45
	Titanium alloy	-	First choice	AH725	≤ 0.03D	30 - 80	0.08	0.08	0.1	0.12	0.15	0.18	0.2	0.2
	Heat-resistance alloys	-	First choice	AH725	≤ 0.03D	20 - 60	0.08	0.08	0.1	0.12	0.15	0.18	0.2	0.2
	High hardened steel	48 - 65 HRC	First choice	AH710	≤ 0.02D	50 - 180	0.08	0.08	0.1	0.13	0.15	0.2	0.2	0.25

Remove excessive chip accumulation with an air blast.
Cutting conditions maybe limited depending on machine power, workpiece H
For the operation with depth of cut which varies (ex.casting skin) and rigidity, and spindle output. When the cutting width, depth, or overhang machining of workpiece materials with interrupted surface, the feed per tooth length is large, set Vc and fz to the lower recommended values and check the (fz) should be set to the lower recommended value shown in the above table. machine power and vibration.

How to clamp the insert	I
1. Clear chips and dust from the pocket.
2. Place the insert in the pocket. The insert can be placed only in one direction.
3. Tighten the screw while pressing the insert into the pocket.	J
How to check the run-out
1. Clamp the insert on the shank.
2. Clamp the shank on a high-precision arbor.	K

3. Measure the run-out on tool presetter or by dial gauge.

Notes:

1. Due to the helical cutting edge, it is important that the

run-out is inspected with the insert clamped on the shank. L

2. Do not use micrometer or caliper to inspect the insert diameter as inaccurate dimensions may be provided. M