Общий каталог Tungaloy 2020 - 2021 - страница 1310

Предыдущая страница Следующая страница

Навигация

TDP L / D = 5

Indexable drill with pilot drill

Adjustable d (Max. 2 to 5 Coolaiameter w mm in ste nt hole Pilith shim sea ps of 0.5 m ot drill InseDC t set m) rt (Tool dia.)OAL LU 内周刃用カートリッジ Cartridge for periphera Cartridge for inner edgePT1/4 LS DCSFMS l edgeDCONMSh6
DesignationDCDCONMSDCSFMSOALLULSInsert(includPilot drill ed in the package)
TDP30-3230 ~ 32324024815060WPMT040208-D3DP08 (ø8)
TDP37-4037 ~ 40405029518570WPMT050308-D3DP10 (ø10)
TDP40-4540 ~ 45405031020070WPMT050308-D3DP12 (ø12)
TDP45-5045 ~ 50405034722570WPMT06T308-D3DP12 (ø12)
TDP60-6560 ~ 655058.5470300120WPMT080412-D3DP12 (ø12)

Diameter is adjustable with shim seat set. (Max. 2 to 5 mm in steps of 0.5 mm) L/D = Hole depth / Drill diameter Pilot drill is included, but inserts are not.

SPARE PARTS

CartridgeClampingscrewCoolantWrench
Designa- tionfor periph- eral edgefor inner edgefor insertWrench for cartridgefor pilot drillhole plug screwfor insertWrench for cartridgefor pilot drillCoolant hole plug screwShim seat set
TDP30-32CW04ACW04BCSTB-2.5SBHM4-8SSHM5-10PT1/4GNT-8DP-2.5Same for cartridgeP-6SW04
TDP37-40CW05ACW05BCSTB-3SBHM4-10SSHM5-10PT1/4GNT-9DP-2.5Same for cartridgeP-6SW05
TDP40-45CW05ACW05BCSTB-3SBHM4-10SSHM6-12PT1/4GNT-9DP-2.5P-3P-6SW05
TDP45-50CW06ACW06BCSTB-3.5DBHM5-14SSHM6-12PT1/4GNT-9DP-3Same for cartridgeP-6SW06
TDP60-65CW08ACW08BCSTB-4MCHHM5-18 (CM5×0.8×18)SSHM6-20PT1/4GNT-15DP-4P-3P-6SW08

Recommended clamping torque (N∙m): CSTB-2.5S = 1.3, CSTB-3S = 2.3, CSTB-3.5D = 2.3, CSTB-4M = 3.5 BHM4-8/BHM4-10 = 2.2, BHM5-14 = 3, CHHM5-18 = 5, SSHM5-10 = 2, SSHM6-12/SSHM6-20 = 3

INSERT PI LOT DRILL

W P M T 0 4 / 0 5 / 0 6 / 0 8 - D 3 D P 0 8 / 1 0 / 1 2

S 80°

OAL

RE

DesignationT313WICSRED1DesignationHSSDCOAL
WPMT040208-D36.352.380.82.86DP08842
WPMT050308-D37.9383.180.83.4DP101048
WPMT06T308-D39.5253.970.83.9DP121255
WPMT080412-D312.74.761.24.4Note : DP08 type drill does notPackage quantity: 1pc

(The chipbreaker shape of WPMT040208-D3 insert is different from the drawing above.) have oil hole. 䖃 : Line up

STANDARD CUTTING CONDITIONS

Workpiece Cutting speed Feed Cautionary points in use

ISOVf
materialc (m/min)(mm/rev)
  • When drilling steel, a water soluble coolant should be used. Coolant pressure of 1MPa

Carbon steels 60 - 70 0.07 - 0.17 or higher and quantity of 10 litter/min or more are essential.

  • For tool-rotating applications, side-lock holder with coolant through hole is recommended.

Alloy steels 60 - 70 0.07 - 0.17 (For standard TDP60-65 and 65-70, please check the toolholder that will be used

because the mounting shank diameter is ø50.)

  • Drilling into stacked plates is not recommended.

Cast iron 70 - 100 0.1 - 0.2 Not suitable for low carbon steels and stainless steels, because of chip control issues.

Note: tool Dia. Smaller than ø37 mm, feed should be set less than 0.13 mm/ rev for steel, 0.15 mm/rev for cast iron.