Общий каталог Tungaloy 2020 - 2021 - страница 1276

Брошюра Tungaloy новая продукция

Брошюра Tungaloy новая продукция

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy зубофрезерование

Каталог Tungaloy зубофрезерование

Каталог Tungaloy глубокое сверление 2

Каталог Tungaloy глубокое сверление 2

	Wki il	Cuttin	g speed:Vc (	m/min)		Fe	ed:f (mm/re	v)
ISO	orpece matera	ø0.1 ~ ø0.3	ø0.3 ~ ø0.5	ø0.5 ~ ø3	ø0.1 ~ ø0.3	ø0.3 ~ ø0.5	ø0.5 ~ ø1	ø1 ~ ø2	ø2 ~ ø3
	Carbon steels, Alloy steels	5 - 20	15 - 30	25 - 60	0.001 - 0.004	0.002 - 0.01	0.005 - 0.05	0.03 - 0.09	0.05 - 0.1
	Stainless steels	2 - 12	6 - 18	10 - 20	0.0005 - 0.004	0.002 - 0.008	0.005 - 0.03	0.01 - 0.04	0.02 - 0.05
	Grey cast irons	5 - 15	10 - 25	20 - 50	0.0005 - 0.004	0.002- 0.012	0.005 - 0.03	0.01 - 0.06	0.03 - 0.12
	Ductile cast irons	5 - 15	10 - 25	20 - 50	0.001 - 0.003	0.002 - 0.01	0.005 - 0.02	0.01 - 0.05	0.03 - 0.1
	Aluminium alloys	10 - 20	10 - 30	20 - 50	0.001 - 0.01	0.005 - 0.03	0.01 - 0.05	0.04 - 0.15	0.06 - 0.2
	Copper / Brass	10 - 20	10 - 30	20 - 50	0.001 - 0.01	0.005 - 0.03	0.01 - 0.05	0.04 - 0.15	0.06 - 0.2
	Heat-resistant alloys	2 - 6	5 - 10	8 - 20	0.0005 - 0.003	0.002 - 0.004	0.002 - 0.004	0.002 - 0.004	※
	High hardened steels	4 - 8	6 - 10	6 - 16	0.0005 - 0.002	0.001 - 0.005	0.005 - 0.02	0.01 - 0.03	0.02 - 0.06

Not recommended

Notes: When the drilling depth is deeper than L/D = 5, use drill pecking every 10 to 50% of the drill diameter.

The above cutting conditions are applied to when a water soluble cutting fluid is used. For drilling a hole smaller than ø0.3 mm, use of a starting drill is recommended.
When setting the drill, the drill run out should be within 0.002 mm on the taper. (Especially for the drill diameter smaller than ø0.5 mm)

D S M - C P

Centering drill for DSM drill

0 0.006-

0 0.006-

OAL

Designation	DC	YH170		DCONMS		OAL	SIG
DSM-CP90	3		䖃		3	38.1	90°
DSM-CP140	3		䖃		3	38.1	140°

䖃 : Line up STANDARD CUTTING CONDITIONS

			Feed:f (	mm/rev)
ISO	Workpiece material	Cutting speed: Vc (m/min)	DSM-CP90	DSM-CP140
	Carbon, Mild and Alloy steels	30 - 80	0.01 - 0.06	0.03 - 0.08
	Grey and ductile cast irons	30 - 80	0.02 - 0.06	0.05 - 0.1
	Aluminium alloys	60 - 120	0.02 - 0.1	0.05 - 0.15
	Stainless steels	15 - 40	0.01 - 0.03	0.02 - 0.06
	High hardened steels (~45HRC)	10 - 40	※	0.01 - 0.05

Not recommended

Notes: For hard materials and stainless steels which have work-hardening nature, DSM-CP140 is recommended.

Above cutting conditions are of using a water-soluble cutting fluid. When using a water-insoluble type, set the cutting speed to lower side.