Общий каталог Tungaloy 2020 - 2021

Брошюра Tungaloy новая продукция

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy зубофрезерование

Каталог Tungaloy глубокое сверление 2

ISO	Workpiece materials	Hardness HB	Selection criteria	Recommended grade	Chip- breaker	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
	Low carbon steels S15C etc	- 200 HB	First choice	AH3135	MM	100 - 250	0.06 - 0.3
	, . C15E4, etc.	- 200 HB	Wear resistance	T3225	MM	200 - 350	0.06 - 0.25
	High carbon steels, alloyed steels S55C SCM440 etc.	- 300 HB	First choice	AH3135	MM	100 - 250	0.06 - 0.3
	, , C55, 42CrMo4, etc.	- 300 HB	Wear resistance	T3225	MM	180 - 300	0.06 - 0.25
	Prehardened steel	30 - 40 HRC	First choice	AH3135	MM	100 - 200	0.06 - 0.25
	NAK80, PX5, etc.	30 - 40 HRC	Wear resistance	T3225	MM	150 - 250	0.06 - 0.2
	Austenitic stainless steel SUS304, SUS316, etc.	- 200 HB	First choice	AH3135	MM	100 - 200	0.06 - 0.25
	X5CrNi18-9, X5CrNiMo17-12-3, etc.	- 200 HB	Wear resistance	T3225	MM	100 - 250	0.06 - 0.2
	Stainless cast steel SCH20XNb, etc. 1.4849, etc.	- -	First choice Fracture resistance	T3225 AH3135	MM MM	60 - 120 60 - 120	0.06 - 0.2 0.06 - 0.2
	Grey cast iron FC250, etc.	150 - 250 HB	First choice	T1215	MM	100 - 350	0.06 - 0.3
	250, etc.	150 - 250 HB	Fracture resistance	AH120	MM	100 - 250	0.06 - 0.3
	Ductile cast iron	150 - 250 HB	First choice	T1215	MM	100 - 350	0.06 - 0.25
	FCD600, etc.
	600-3, etc.	150 - 250 HB	Fracture resistance	AH120	MM	80 - 200	0.06 - 0.3
	Titanium alloy Ti-6Al-4V, etc.	- 40 HRC	First choice	AH3135	MM	30 - 60	0.06 - 0.2
	Heat resistant alloy Inconel718, etc.	- 40 HRC	First choice	AH120	MM	10 - 40	0.04 - 0.16
	Hardened steel SKD61, etc. X40CrMoV5-1, etc.	40 - 50 HRC	First choice	AH3135	MM	80 - 130	0.04 - 0.16
	Hardened steel SKD11, etc.X153CrMoV12, etc.	50 - 60 HRC	First choice	AH120	MM	50 - 70	0.02 - 0.08

SKD11, etc. X153CrMoV12, etc. 50 - 60 HRC First choice AH120 50 - 70 0.02 - 0.08 G

Tool offset To eliminate uncut amount in face milling operation, adjust the programming according to the offset (L) listed below. H RE

Designation	RE	BS	L
SNMU120608HNEN-MM	0.8	1.4	1.3
SNMU120612EN-MM	1.2	-	1.7
SNMU120620EN-MM	2	-	2.5

DCX

J

The following table shows the amount left over cut (t) when the cutter is considered as a shoulder milling cutter.

t
		/ap (mm) Designation	1	2	3	4	5	6	7	8	9	9.5
		SNMU120608HNEN-MM	0.01	0.04	0.05	0.05	0.07	0.09	0.14	0.2	0.27	0.27
RE	ap	SNMU120612EN-MM SNMU120620EN-MM	- -	0 0	0 0	0.01 0	0.02 0.02	0.05 0.05	0.09 0.09	0.15 0.15	0.22 0.22	0.25 0.25

Общий каталог Tungaloy 2020 - 2021 - страница 893

Навигация

DCX

DCX

J

L

M

Общий каталог Tungaloy 2020 - 2021 - страница 893

Навигация

DCX

DCX

J

L

M

Отправьте заявку

На подбор необходимой оснастки и оборудования