WF CDX DCONMSH DMINCDX CTIR/L Internal grooving and turning toolholder LH Insert: DMIN CW LF Seat size 2:DGIM, DGIS Seal cap Right hand (R) shown. Designation CW DMIN Seat size CDX DCONMS H LF (1) LH WF Insert Torque* CTIR/L16-2T08-D250 2 25 2 8 16 14 125 - 16.5 DGIM..., DGIS... 5 CTIR/L20-2T06-D250 2 25 2 6 20 18 160 40 15.8 DGIM..., DGIS... 5 External CTIR/L20-3T06-D250 3 25 3 6 20 18 160 40 15.8 DTI..., DTX... 5 CTIR/L25-3T05-D250 3 25 3 5.1 25 23 200 40 17.5 DTI..., DTX... 5 CTIR/L25-3T08-D320 3 32 3 8 25 23 200 40 21.5 DTI..., DTX... 5 CTIR/L32-3T10-D400 3 40 3 10 32 30 250 60 27 DTI..., DTX... 5 Internal CTIR/L20-4T06-D250 4 25 4 6 20 18 160 40 15.8 DTI..., DTX... 5 CTIR/L25-4T08-D320 4 32 4 8 25 23 200 40 21.5 DTI..., DTX... 5 CTIR/L32-4T04-D310 4 31 4 4 32 30 250 60 20.8 DTI..., DTX... 5 Face CTIR/L32-4T10-D400 4 40 4 10 32 30 250 60 27 DTI..., DTX... 5 CTIR/L25-5T05-D310 5 31 5 5 25 23 200 60 17.3 DTI..., DTX... 8.5 CTIR/L32-5T10-D400 5 40 5 10 32 30 250 60 27 DTI..., DTX... 8.5 Parting CTIR/L32-6T04-D310 6 31 6 4 32 30 250 60 20.8 DTI..., DTX... 8.5 CTIR/L32-6T10-D400 6 40 6 10 32 30 250 60 27 DTI..., DTX... 8.5 Others CTIR/L32-8T05-D370 8 37 8 5 32 30 250 60 21.3 DTI..., DTX... 8.5 CTIR/L40-8T05-D420 8 42 8 5.8 40 38 300 65 25.8 DTI..., DTX... 8.5 (1) L1 is calculated with the groove width CW in the above table. *Torque: Recommended clamping torque (N∙m) When using the inserts that are not in the above SPARE PARTS Groove width Min. diameter Designation Clamping screw Wrench Seal cap Thread type for connection INSERT CW DMIN CTIR/L16-2T08-D250 CM5X0.8X10-A P-4 CA-16 M6 DGM / DGS / SGN / DGL / DTM 3 50 CTIR/L20-2T06-D250 CM5X0.8X12-A P-4 CA-20 M6 DGM / DGS / SGN / DTM / DGL 4 50 CTIR/L20-3T06-D250 CM5X0.8X12-A P-4 CA-20 M6 DGM / DGS / DTM / DGL 5 60 DGM / DGS / DTM / DGL 6 60 CTIR/L25-3T05-D250 CM5X0.8X16-A P-4 CA-25 R1/8" DGM / DGS / DTM 8 70 CTIR/L25-3T08-D320 CM5X0.8X16-A P-4 CA-25 R1/8" DTE / DGG 3 40 CTIR/L32-3T10-D400 CM5X0.8X16-A P-4 CA-32 R1/8" DTE / DGG 4 40 CTIR/L20-4T06-D250 CM5X0.8X12-A P-4 CA-20 M6 DTE / DGG 5 50 CTIR/L25-4T08-D320 CM5X0.8X16-A P-4 CA-25 R1/8" DTE / DGG 6 50 CTIR/L32-4T04-D310 CM5X0.8X16-A P-4 CA-32 R1/8" DTE / DGG 8 62 CTIR/L32-4T10-D400 CM5X0.8X16-A P-4 CA-32 R1/8" DTR 3 38 DTR 4 38 CTIR/L25-5T05-D310 CM6X1X16-A P-5 CA-25 R1/8" DTR 5 43 CTIR/L32-5T10-D400 CM6X1X20-A P-5 CA-32 R1/8" DTR 6 46 CTIR/L32-6T04-D310 CM6X1X20-A P-5 CA-32 R1/8" DTR 8 56 CTIR/L32-6T10-D400 CM6X1X20-A P-5 CA-32 R1/8" CTIR/L32-8T05-D370 CM6X1X20-A P-5 CA-32 R1/8" CTIR/L40-8T05-D420 CM6X1X25-A P-5 CA-40 R1/8" Reference pages: Inserts → F098 - F113, Standard cutting conditions → F113 F096 www.tungaloy.com