Общий каталог Tungaloy 2020 - 2021 - страница 957

Предыдущая страница Следующая страница

Навигация

Hard-Cutting speedFeedper tooth:fz (mm/t)t
Workpiece materialsnessGradesVc (m/min)MJ NMJAJ ser
HBT/E/HPA06T/E/HPA10T/EPA15T/E/HPA06 T/E/HPA10 T/EPA15 T/EPA15T/E/HPA10 In
Low carbon steel (SS400, S15C , etc. E275A, C15E4, etc.- 200AH3135100 - 220100 - 250100 - 2500.05 - 0.15 0.08 - 0.2 0.08 - 0.25 0.08 - 0.15- r
High carbon steel S45C, etc. C45, etc.200 - 300AH3135100 - 170100 - 200100 - 2300.05 - 0.12 0.08 - 0.15 0.08 - 0.2 0.08 - 0.15- oolholde
Alloy steel SCM440, etc. 42CrMo4, etc.150 - 300AH3135100 - 170100 - 200100 - 2300.05 - 0.12 0.08 - 0.15 0.08 - 0.2 0.08 - 0.15- Ext. T
Tool steel SKD61, etc. X40CrMoV5-1, etc30 - 40 HRCAH3135100 - 120100 -150100 - 1800.05 - 0.12 0.08 - 0.15 0.08 - 0.2 0.08 - 0.15- holder
Stainless steel SUS304, etc. X5CrNi18-9, etc.-AH313580 - 15080 - 20090 - 2000.05 - 0.15 0.08 - 0.2 0.08 - 0.2 0.08 - 0.15- Int. Tool
Grey cast iron FC250, etc. 250, etc.150 - 250AH120 T1215100 - 200 150 - 250100 - 250 150 - 300140 - 250 200 - 3000.05 - 0.15 0.08 - 0.2 0.08 - 0.25 0.08 - 0.15 0.05 - 0.12 0.08 - 0.15 0.08 - 0.18 -- - ng
Ductile cast iron FCD450, etc. 450-10S, etc.150 - 250AH120 T121580 - 150 100 - 20080 - 200 130 - 250110 - 200 150 - 2500.05 - 0.15 0.08 - 0.2 0.08 - 0.25 0.08 - 0.15 0.05 - 0.12 0.08 - 0.15 0.08 - 0.18 -- - hreadi
Aluminium Si < 13%-KS05F-300 - 1000-- - - -0.08 - 0.22 T
Aluminium Si ≥ 13%-KS05F-100 - 200-- - - -0.08 - 0.22 oving
Titanium alloys Ti-6Al-4V, etc.-AH12020 - 5020 - 6020 - 600.05 - 0.1 0.08 - 0.15 0.08 - 0.18 0.08 - 0.15- Gro
Heat-resistant alloys Inconel 718, etc.-AH12020 - 3520 - 4020 - 400.03 - 0.08 0.05 - 0.13 0.07 - 0.15 0.07 - 0.15- tool
  • When you use the NMJ chipbreaker, please set up the feed less than 0.15 mm/t.
  • Cutting conditions maybe limited depending on machine power, workpiece
  • Remove excessive chip accumulation with an air blast. rigidity, and spindle output. When the cutting width, depth, or overhang
  • For the operation with depth of cut which varies (ex.casting skin) and length is large, set Vc and fz to the lower recommended values and check

machining of workpiece materials with interrupted surface, the feed per tooth the machine power and vibration. H

(fz) should be set to the lower recommended value shown in the above table.

HardnessCuttingspeedFeedper tooth:fz (mm/t)l
ISOWorkpiece materialsHBGradesVc (m/min)MJNMJAJmil
TLA10TLA15TLA10TLA15TLA15TLA10nd
Low carbon steel SS400, S15C, etc. E275A, C15E4, etc.- 200AH3135100 - 250100 - 2500.08 - 0.180.08 - 0.220.08 - 0.15-E
High carbon steel S45C, etc. C45, etc.200 - 300AH3135100 - 200100 - 2700.08 - 0.140.08 - 0.180.08 - 0.15-g tool
Alloy steel SCM440, etc. 42CrMo4, etc.30 - 40 HRCAH3135100 - 150100 - 1800.08 - 0.140.08 - 0.180.08 - 0.15-Drillin
Stainless steel SUS304, etc. X5CrNi18-9, etc.-AH313580 - 20090 - 2000.08 - 0.150.08 - 0.180.08 - 0.15-stem
Grey cast iron FC250 etc150 - 250AH120100 - 250140 - 2500.08 - 0.180.08 - 0.250.08 - 0.15-g Sy
, . 250, etc.T1215150 - 250150 - 2500.08 - 0.150.08 - 0.18--olin
Ductile cast iron FCD450, etc. 450-10S, etc.150 - 250AH120 T121580 - 200 150 - 250110 - 200 150 - 2500.08 - 0.18 0.08 - 0.150.08 - 0.25 0.08 - 0.180.08 - 0.15 -- -To de
Aluminium Si < 13%-KS05F300 - 1000----0.08 - 0.22's Gui
Aluminium Si ≥ 13%-KS05F100 - 200----0.08 - 0.22User
Titanium alloys Ti-6Al-4V, etc.-AH12020 - 6020 - 600.08 - 0.150.08 - 0.180.08 - 0.15-ex
Heat-resistant alloys Inconel 718, etc.-AH12020 - 4020 - 400.05 - 0.130.07 - 0.150.07 - 0.15-Ind
  • When using NMJ chipbreaker, please set up the feed not to exceed 0.15 mm/t.