Общий каталог Tungaloy 2020 - 2021

V F X * * - 0 2 . . .

				RE DCh9	LF APMX	DCSFMS CRKS		1 ≤	0° APMX = Ma CRKS = Co	x. depth nnection	of cut screw size
Designation	AH725	NOF	FHA	DC	DCSFMS APMX	RE(1)	CRKS	LF	Wrench T	orque	fz (mm/t)
VFX100L00.6R20-02S06	�	2	0º	10	9.6 0.6	2	S06	12.5	KEYV-S06	10	0.3-0.6
VFX120L01.0R25-02S08	�	2	0º	12	11.5 1.0	2.5	S08	11.1	KEYV-S08	15	0.5-1.0
VFX160L01.1R30-02S10	�	2	0º	16	15.2 1.1	3	S10	20	KEYV-S10	28	0.55-1.1
VFX200L01.5R33-02S12	�	2	0º	20	18.3 1.5	3.3	S12	17.5	KEYV-S12	28	0.75-1.5
1) Corner radius for CAM programming											�: Line up

Note: Please use tapered neck shank or tungsten shank for VFX head. Square * Recommended clamping torque N·m 2 pieces per package

Radius V F X * * - 0 4 . . .

Ball

chamfering R Slotting

APMX = Max. depth of cut CRKS = Connection screw size

		Designation	AH725		NOF	FHA	DC	DCSFMS APMX		RE	KAPR	CRKS	LF	Wrench Torque*		fz (mm/t)
	VFX120L0.60R18H04S08			z	4	20º	12	11.5	0.6	1.8	97º	S08	16.5	KEYV-S08	15	0.16-0.67
	VFX160L0.80R22H04S10			z	4	20º	16	15.4	0.8	2.2	97º	S10	20.5	KEYV-S10	28	0.2-0.75
33333333333	* Recommended clamping torque (N·m)															z: Line up

2 pieces per package 44 STANDARD CUTTING CONDITIONS High feed milling (VFX)

			ø10	ø12	ø16	ø20
ISO Workpiece material	Hardness V	Cutting speed c (m/min)	Feed per tooth fz (mm/t)	Feed per tooth fz (mm/t)	Feed per tooth fz (mm/t)	Feed per tooth fz (mm/t)	Width of cut ae (mm)
Low carbon steels S45C, S55C, etc. C45, C55, etc.	- 300 HB	100 - 200	0.3 - 0.7	0.4 - 0.8	0.5 - 0.9	0.6 - 1	0.6 x DC
High carbon steels SCM440, SCr415, etc. 42CrMo4, 15Cr3, etc.	- 300 HB	80 - 180	0.2 - 0.6	0.3 - 0.7	0.4 - 0.8	0.5 - 0.9	0.6 x DC
Prehardened steel PX5, NAK80, etc.	30 - 40 HRC	80 - 160	0.2 - 0.5	0.2 - 0.5	0.3 - 0.6	0.3 - 0.6	0.6 x DC
Stainless steels SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	- 200 HB	60 - 100	0.2 - 0.6	0.2 - 0.6	0.3 - 0.7	0.3 - 0.7	0.6 x DC
Grey cast irons FC250, FC300, etc. 250, 300, etc.	150 - 250 HB	100 - 220	0.3 - 0.7	0.4 - 0.8	0.5 - 0.9	0.6 - 1	0.6 x DC
Ductile cast irons FCD400, etc. 400-15S, etc.	150 - 250 HB	100 - 220	0.2 - 0.6	0.3 - 0.7	0.4 - 0.8	0.5 - 0.9	0.6 x DC
Titanium alloys Ti-6Al-4V, etc.	-	40 - 80	0.2 - 0.5	0.2 - 0.5	0.2 - 0.6	0.2 - 0.6	0.25 x DC
Heat-resistant alloys Inconel 718, etc.	-	20 - 40	0.1 - 0.3	0.1 - 0.3	0.1 - 0.3	0.1 - 0.3	0.25 x DC
Hardened steel SKD61, SKT4, etc. X40CrMoV5 1, 55NiCrMoV6, etc.	40 - 50 HRC	40 - 80	0.2 - 0.4	0.2 - 0.4	0.3 - 0.5	0.3 - 0.5	0.45 x DC
Hardened steel SKD11, SKH, etc. X153CrMoV12, HS18-0-1, etc.	50 - 60 HRC	20 - 60	0.1 - 0.2	0.1 - 0.2	0.1 - 0.3	0.1 - 0.3	0.25 x DC

or morooor mor morrmoremoororere

Feed per tooth should not exceed the maximum value for each product.

Общий каталог Tungaloy 2020 - 2021 - страница 1132