Общий каталог Tungaloy 2020 - 2021

ISO	Workpiece material	Hardness	Grade	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
	Low carbon steel S15C, etc. C15E, etc.	- 200HB	AH3135	100 - 250	0.1 - 0.25
	Alloy steel S55C, etc. C55, etc.	- 300HB	AH3135	100 - 230	0.1 - 0.2
	Prehardened steel NAK80, PX5, etc.	30 - 40HRC	AH3135	100 - 230	0.1 - 0.2
	Stainless steel SUS304, etc. X5CrNi18-9, etc.	-	AH3135	90 - 180	0.1 - 0.25
	Grey cast iron FC250, etc. 250, etc.	150 - 250HB	AH120	140 - 250	0.1 - 0.25
	Ductile cast iron FCD400, etc. 450-10S, etc.	150 - 250HB	AH120	110 - 200	0.1 - 0.25
	Titanium alloys Ti-6Al-4V, etc.	-	AH120	30 - 60	0.08 - 0.2
	Superalloys Inconel 718, etc.	-	AH120	20 - 50	0.06 - 0.1
	Hdd tl SKD61, etc. X40CrMoV5-1, etc.	40 - 50HRC	AH120	45 - 70	0.08 - 0.15
	arene see SKD11, etc. X153CrMoV12, etc.	50 - 60HRC	AH120	40 - 65	0.06 - 0.1

X153CrMoV12, etc. F

ISO	Workpiece material	Hardness HB	Grade	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
	Low carbon steel S15C, etc. C15E, etc.	- 200	AH725	100 - 250	0.1 - 0.25
	High carbon steel S45C, S55C, etc. C45, C55, etc.	200 - 300	AH725	100 - 230	0.1 - 0.2
	Alloy steel SCM440, SCr415, etc. 42CrMo4, etc.	150 - 300	AH725	100 - 230	0.1 - 0.2
	Tool steel D2, etc. X153CrMoV12, etc.	- 300	AH725	100 - 180	0.1 - 0.2
	Stainless steel SUS304, etc. X5CrNi18-9, etc.	-	AH140	90 - 180	0.1 - 0.25
	Grey cast iron FC250, etc. 250, etc.	150 - 250	AH120	140 - 250	0.1 - 0.25
	Ductile cast iron FCD400, etc. 450-10S, etc.	150 - 250	AH120	110 - 200	0.1 - 0.25
	Superalloys Inconel 718, Ti-6Al-4V, etc.	-	AH725	20 - 50	0.08 - 0.2

* When using LQMU11 inserts, see page H170 for proper feed per tooth setting.

For applications with poor chip evacuation, use air gun to remove chips from the machining area to avoid chip re-cutting and part damage.
To machine cast surface with unstable cutting depths or interruptions, it is recommended to lower the feed rate (fz) to the lowest parameter in the recommended range.
Rigidity of the machine and/or workpiece and the spindle power capability greatly inﬂ uence the cutting conditions. For applications with large cutting width/depth and/or

long tool overhang, start with a Vc and fz in the lower range of the recommended cutting parameters and monitor the machine stability.

Общий каталог Tungaloy 2020 - 2021 - страница 993