Общий каталог Tungaloy 2020 - 2021

Брошюра Tungaloy новая продукция

Каталог Tungaloy глубокое сверление 1

Каталог Tungaloy инструмент для автоматов швейцарского типа

Каталог Tungaloy зубофрезерование

Каталог Tungaloy глубокое сверление 2

		Cutting			Fe	ed:f (mm/r	ev)
ISO	Workpiece material	speed				DC(mm)
		Vc (m/min)	ø6 - 7.9	ø8 - 9.9	ø10 - ø11.9	ø12 - ø13.9	ø14 - ø15.9	ø16 - ø19.9	ø20 - ø25.9
	Low carbon steels (C < 0.3) SS400, SM490, S25C, etc. C15E4, E275A, E355D, etc.	80 - 140	0.09 - 0.13	0.12 - 0.25	0.15 - 0.28	0.18 - 0.3	0.20 - 0.35	0.25 - 0.45	0.25 - 0.45
	High carbon steels (C > 0.3) S45C, S55C, etc. C45, C55, etc.	70 - 120	0.09 - 0.13	0.12 - 0.25	0.15 - 0.28	0.18 - 0.3	0.2 - 0.35	0.25 - 0.45	0.25 - 0.45
	Low alloy steels SCM415, etc. 18CrMo4, etc.	70 - 120	0.08 - 0.13	0.11 - 0.25	0.14 - 0.28	0.16 - 0.32	0.18 - 0.35	0.23 - 0.4	0.25 - 0.45
	Alloy steels SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	40 - 90	0.08 - 0.13	0.11 - 0.25	0.14 - 0.28	0.16 - 0.32	0.18 - 0.35	0.23 - 0.4	0.25 - 0.45
	Stainless steels SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	30 - 70	0.08 - 0.1	0.1 - 0.15	0.12 - 0.18	0.14 - 0.2	0.16 - 0.24	0.16 - 0.26	0.18 - 0.3
	Grey cast irons FC250, etc.	80 - 180	0.12 - 0.18	0.15 - 0.3	0.20 - 0.35	0.25 - 0.4	0.3 - 0.45	0.35 - 0.55	0.35 - 0.6
	GG25, etc.
	Ductile cast irons FCD700, etc. GGG70, etc.	80 - 140	0.12 - 0.18	0.15 - 0.3	0.20 - 0.35	0.25 - 0.4	0.3 - 0.45	0.35 - 0.55	0.35 - 0.6
	Aluminium alloys ADC12, etc. AlSi11Cu3, etc.	80 - 220	0.1 - 0.2	0.2 - 0.35	0.25 - 0.4	0.3 - 0.45	0.35 - 0.5	0.4 - 0.6	0.5 - 0.75
	Titanium alloys Ti-6Al-4V, etc.	20 - 50	0.05 - 0.07	0.06 - 0.12	0.08 - 0.15	0.1 - 0.28	0.12 - 0.2	0.14 - 0.22	0.18 - 0.27
	Nickel-based alloys	20 - 50	0.05 - 0.07	0.06 - 0.11	0.08 - 0.13	0.1 - 0.15	0.12 - 0.18	0.12 - 0.22	0.14 - 0.22
	Hardened steel	20 - 50	0.05 - 0.07	0.06 - 0.12	0.08 - 0.15	0.1 - 0.18	0.12 - 0.2	0.14 - 0.22	0.16 - 0.25

- Cutting conditions in the above table show standard cutting conditions. - Machined hole diameter may change depending upon the rigidity of the - Cutting conditions may change due to the rigidity and power of the machine machine tool or cutting conditions. and the workpiece material. - In case of L/D = 8,12 drill, the recommended range of cutting speeds and feeds is between the minimum and median values listed above.

CLAMPING KEY FO R MEASURING U N - C L A M PI N G TORQUE

To check drill body duration, measure un-clamping torque by using a torque-driver

Recommended value of un-clamping torque that means usable limit of a drill body shown in below table.

Head Designation	（N・m） Recommended value that means usable	（cN・m） of un-clamping torque limit of a drill body
DM100-109	0.2	20
DM110-119	0.2	20
DM120-129	0.25	25
DM130-139	0.25	25
DM140-149	0.3	30
DM150-159	0.3	30
DM160-169	0.35	35
DM170-179	0.35	35
DM180-189	0.4	40
DM190-199	0.4	40

can be connect

Общий каталог Tungaloy 2020 - 2021 - страница 1252

Навигация

CLAMPING KEY FO R MEASURING U N - C L A M PI N G TORQUE

To check drill body duration, measure un-clamping torque by using a torque-driver

Общий каталог Tungaloy 2020 - 2021 - страница 1252

Навигация

CLAMPING KEY FO R MEASURING U N - C L A M PI N G TORQUE

To check drill body duration, measure un-clamping torque by using a torque-driver

Отправьте заявку

На подбор необходимой оснастки и оборудования