Общий каталог Tungaloy 2020 - 2021 - страница 874

Предыдущая страница Следующая страница

Навигация

ShoulderSmall depthDrilling
millingplungingRampingPlunging(Helical feed)Enlarging hole

W

0 9 type

ae

øD1, 2

Tool dia.Ma depthx. of cutMax. plunging depthM ram anax. ping gleMax. c wid plunutting th in gingMi mach din. ining a.M mach diax. ining a.Max. c wid enlautting th in rging
DesignationDCXAP SWMT 09ZERMX SWMT 09UERARM SWMT 09ZERPX SWMT 09UERSWMT 09ZERW SWMT 09UERøD SWMT 09ZER1 SWMT 09UERøD SWMT 09ZER2 SWMT 09UERa SWMT 09ZERe SWMT 09UER
EXSW09M025...251.510.34.8677.53433474716.516
EXSW09M032...321.510.32.73.277.54847616123.523
TXSW09M040...401.510.31.82.177.56463777731.531
TXSW09M050...501.510.31.21.477.58483979741.541

1 5 type

Tool dia.M depthax. of cutMax. plunging depthMax. ramping angleMax. wid pluncutting th in gingMin. machining dia.Max. machining dia.Max. wid enlacutting th in rging
DesignationDCXAP SWMT 15ZERMX SWMT 15UERARMPXSWMT 15ZERW SWMT 15UERøD1øD2a SWMT 15ZERe SWMT 15UER
TXSW15M050B...502.520.74.8°12.513.570953635
TXSW15M063B...632.520.72.9°12.513.5961214948
TXSW15J, M080B...802.520.72°12.513.51301556665
TXSW15J, M100B...1002.520.71.4°12.513.51701958685
TXSW15J, M125B...1252.520.71°12.513.5220245111110
TXSW15J, M160B...1602.520.70.7°12.513.5290315146145

45°

85°

88°

90°

Others

TOOL GEOMETRY FO R PROGRAMMING

t2

KAPR

RE

LE t1 RPG

0 9 type

APMX(mm)Actual cornerLE (mm)KAPRProgrammedUncut amount: t1 (mm)Overcut amount: t2 (mm)
SWMTSWMTradiusSWMTSWMTSWMTSWMTcorner radiusSWMTSWMTSWMTSWMT
09ZER09UERRE (mm)09ZER09UER09ZER09UERRPG09ZER09UER09ZER09UER
1.5117.47.912°7°11.30.81--
1.5117.47.912°7°1.51.210.76--
1.5117.47.912°7°21.120.7-0.02
1.5117.47.912°7°2.51.030.650.010.15
1.5117.47.912°7°30.940.590.110.33

1 5 type

APMX(mm)Actual cornerLE (mm)KAPRProgrammedUncut amount: t1 (mm)Overcut amount: t2 (mm)
SWMTSWMTradiusSWMTSWMTSWMTSWMTcorner radiusSWMTSWMTSWMTSWMT
15ZER15UERRE (mm)15ZER15UER15ZER15UERRPG15ZER15UER15ZER15UER
2.52212.713.814°10°3.52.11.85--
2.52212.713.814°10°41.991.77--
2.52212.713.814°10°4.51.881.69-0.03
2.52212.713.814°10°51.781.610.010.13

- When programming for CAM, the tool should be considered as a radius cutter. Usually, the corner radius should be set in SWMT**ZER insert: RPG = 4.5 mm, SWMT**UER insert: RPG = 4 mm. If a larger radius is used, overcutting may occur. The above table shows the uncut (t1) and overcut (t2) amounts for the programmed corner radius.