Общий каталог Tungaloy 2020 - 2021 - страница 1623

Предыдущая страница Следующая страница

Навигация

Turning Tools B

Compensations for DNMG / TNMG -SW / -FW

Compensations ⑤ Program compensations for tapered surface

ForTNMG-SW/-FW(TypeJ)o oolholderC
X-axis compensation values for plus-tapered surJ 93 . T face (increase in diameter)
Nose radiusExt Taper angleα (θ )
R0.4 (mm)0 05 10 15 20 0 0 -0.01 -0.0125 -0.0230 -0.0335 40 45 50 55 60 65 70 75 80 85 90 -0.04 -0.05 -0.07 -0.10 -0.14 -0.18 -0.25 -0.28 -0.28 -0.27 -0.27 0 er
R0.800.01 0.02 0.03 0.040.040.040.03 0.02 0.00 -0.02 -0.06 -0.11 -0.19 -0.22 -0.20 -0.19 -0.21 0 hold
R1.2 Z-axi0 s com0.02 0.05 0.07 0.08 pensation value for minus0.09 -tape0.10 red su0.09 0.08 0.06 0.03 -0.02 -0.10 -0.22 -0.26 -0.25 -0.25 -0.31 0 Int. Tool rface (reduction in diameter)D
R0.4 R0.8 R1.2 Nose radius (mm)-25 0.4 0.3 0.4Taper angleα(θ) -20 -15 -10 -5 2 0.42 0.42 0.41 0.40 5 0.32 0.33 0.34 0.33 2 0.36 0.38 0.39 0.37ThreadingE
For X-axi Nose radius (mm)0 TN s com5 10 15 20 MG-SW/-FW(Ty pensation values for plus25 pe -tape30 G) red sur35 40 45 50 55 60 65 70 75 80 85 90 G 91o Grooving l face (increase in diameter) Taper angleα (θ )F
R0.4 R0.8 R1.20 0 00.00 -0.01 -0.01 -0.02 0.01 0.02 0.02 0.03 0.03 0.06 0.08 0.09-0.03 0.02 0.10-0.04 0.02 0.11-0.05 -0.07 -0.09 -0.12 -0.16 -0.22 -0.28 -0.29 -0.29 -0.29 -0.32 0 0.01 -0.01 -0.03 -0.06 -0.10 -0.17 -0.25 -0.25 -0.25 -0.28 -0.40 0 0.10 0.09 0.07 0.04 -0.01 -0.09 -0.18 -0.18 -0.18 -0.20 -0.34 0 iniature tooG
R0.4 For X-axi Nose radius (mm)0 0 TN s com5 10 15 20 -0.03 -0.05 -0.08 -0.10 MG-SW/-FW(Ty pensation values for plus25 -0.13 pe -tape30 -0.13 F) red sur35 40 45 50 55 60 65 70 75 80 85 90 -0.11 -0.10 -0.09 -0.08 -0.07 -0.06 -0.05 -0.05 -0.04 -0.03 -0.02 0 F 91o M Milling cutter face (increase in diameter) Taper angleα (θ )H
R0.8 R1.20 0-0.04 -0.05 -0.07 -0.09 -0.03 -0.04 -0.05 -0.07-0.12 -0.09-0.10 -0.05-0.07 -0.05 -0.03 -0.01 0.01 0.03 0.05 0.07 0.09 0.11 0.13 0 -0.01 0.03 0.07 0.11 0.15 0.18 0.22 0.25 0.28 0.32 0.35 0 EndmillI
Com o ach espec DNM Nosepe ieve t tive in G- Radiunsations⑥Prog he correct corner radius dim sert styles. SW/-FW(Type J) s Deviation on the corner radius Compensate radius byram ensionco on theDrilling tool System mpensation for corner radii (proceed after④) workpiece, compensate the tool position, using the values listed below forJ
R0 R0.4 .80 0 0.02 +0.20ToolingK
R1 TNM Nose.2 G- Radiu0.10 +0.34 SW/-FW(Type J) s Deviation on the corner CompensateTN NosMG- e RadiuUser's Guide SW/-FW(Type G,Type F) s Deviation on the corner CompensateL
Nose RadiusDeviation on the corner radiusCompensate radius by
R0.400
R0.80.02+0.20
R1.20.10+0.34
Nose RadiusDeviation on the corner radiusCompensate radius byNose RadiusDeviation on the corner radiusCompensate radius by
R0.400R0.400
R0.80.03+0.13R0.80.02+0.15
R1.20.11+0.36R1.20.09+0.38