Каталог Sumitomo монолитные фрезы

Каталог Sumitomo инструмент для отрезки

Каталог Sumitomo токарные резцы (державки) для наружного точения

Общий каталог Sumitomo 2012

Каталог Sumitomo сплавы и режимы

Каталог Sumitomo специальные торцевые фрезы

Каталог Sumitomo фрезы со сменными пластинами

GSBHGS MILL HardBallNose Endmills 20000SF

22	GS		Hardened Steel
			45 to 55 55 to 60 60 to 65
	HARD		HRC	HRC	HRC
		GGGSGGG
FlutesFlutes

Coating Side Milling Face Milling R-Groove Milling Profile Milling

RE +0.003 -0.007

25°

Helix Angle

Body

APMX LU (Neck portion for ø5 and below) LF

				Dimensi	ons(mm)
Cat. No.	Stock	Radius RE	Cutting diameter DC	Depth of cut APMX	Cutting Edge Length LU	Total Length LF	Shank diameter DMM
GSBH 20020SF	D	0.20	0.4	0.4	0.6	50	4
20030SF	D	0.30	0.6	0.6	0.9	50	4
20050SF	D	0.50	1.0	1.0	1.5	50	4
20075SF	D	0.75	1.5	1.5	2.3	50	4
20100SF	D	1.00	2.0	2.0	3.0	60	6
GSBH 20125SF	D	1.25	2.5	2.5	3.8	60	6
20150SF	D	1.50	3.0	3.0	4.5	60	6
20200SF	D	2.00	4.0	4.0	6.0	70	6
20250SF	D	2.50	5.0	5.0	7.5	80	6
20300SF	D	3.00	6.0	6.0	Q	80	6
GSBH 20400SF	D	4.00	8.0	8.0	Q	90	8
20500SF	D	5.00	10.0	10.0	Q	100	10
20600SF	D	6.00	12.0	12.0	Q	110	12

Grade: ACF07D

Recommended Cutting Conditions

1. When depth of cut is lowered, feed rate can be increased further. 2. If the machine cannot achieve the recommended spindle speed, please use the max. spindle speed I available. In this case, lower the feed rate by the same ratio. 3. If cutting noise and vibration are present, please change the cutting conditions accordingly. p

Radius Milling

Work Material Cutting Conditions	Middle Hard Pre-hardened St (40 to 50	ened Steel eel, Die Steel HRC)	Hardene SKD (50 to 55	d Steel 61 HRC)	Hardene SKD (55 to 60	d Steel 11 HRC)	Hardene SKH (60 to 6	d Steel 55 5HRC)
RE(mm)	Spindle Speed (min`－`1)	Feed Rate (mm/min)	Spindle Speed (min`－`1)	Feed Rate (mm/min)	Spindle Speed (min`－`1)	Feed Rate (mm/min)	Spindle Speed (min`－`1)	Feed Rate (mm/min)
0.20	50,000	500	50,000	500	50,000	500	50,000	500
0.30	50,000	800	50,000	800	50,000	800	50,000	700
0.50	50,000	1,400	50,000	1,400	50,000	1,300	42,000	1,000
0.75	50,000	2,000	50,000	2,000	37,300	1,400	28,000	1,000
1.00	38,100	2,100	38,100	2,100	28,000	1,400	21,000	1,000
1.25	30,500	2,100	30,500	2,100	22,400	1,400	16,800	1,000
1.50	25,400	2,100	25,400	2,100	18,700	1,400	14,000	1,000
2.00	19,100	2,100	19,100	2,100	14,000	1,400	10,500	1,000
2.50	15,300	2,100	15,300	2,100	11,200	1,400	8,400	1,000
3.00	12,700	2,100	12,700	2,100	9,300	1,400	7,000	1,000
4.00	9,500	2,100	9,500	2,100	7,000	1,400	5,300	1,000
5.00	7,600	2,100	7,600	2,100	5,600	1,400	4,200	1,000
6.00	6,400	2,100	6,400	2,100	4,700	1,400	3,500	1,000
Sdd Dhf ap		0.0	8DC			0.0	5DC
tanar ept-o-cut pf		0.2	5DC			0.1	5DC

2 Flutes

6 Flutes

DLC

Long Neck Uncoated CBN PCD

Каталог Sumitomo монолитные фрезы - страница 112

Навигация

GSBHGS MILL HardBallNose Endmills 20000SF

Каталог Sumitomo монолитные фрезы - страница 112

Навигация

GSBHGS MILL HardBallNose Endmills 20000SF

Отправьте заявку

На подбор необходимой оснастки и оборудования