Общий каталог Palbit - страница 349

Предыдущая страница Следующая страница

Навигация

technical data

Dados técnicos | Datos técnicos

cutting parameters |cutting parameters |D
D
Parâmetros de corte | Parámetros de corteParâmetros de corte | Parámetros de corte

Feed recommendations and geometry descriptions Grooving & Parting Off Feed recommendations and geometry descriptions Grooving & Parting Off

GP…02-MC GCMX-... Radial feed

Radial feed Inserts Width (mm) Inserts Width (mm) Medium Parting Off Width (W) [mm] Width (W) [mm]

Recommended for parting off, 6,0

4,0thin walled tubes and smallMedium Parting Off
diameter components in all5,0
materials.Most efficient on stainless
3,04,0steel and most types of steel at
The positive geometry eliminatesmoderate feed rates.
2,0the risk of built-up edge.3,0Superior straightness of cut

Low cutting forces resulting in 2,0 0 0,05 0,10 0,15 0,25 0,30 reducedvibration. 0 0,10 0,20 0,30 0,40 0,50 Feed fn (mm/rot.)

Feed fn (mm/rot.)

GP…02-MG SANCAR-... Radial feed

Radial feed Inserts Width (mm) Inserts Width (mm) Width (W) [mm] Width (W) [mm]

Medium Grooving 6,0 5,0 Medium Parting Off Outstanding chip control. 5,0

Optimizer to minimize pips and

4,0Reduces chip width giving good4,0burrs on components.
surfaces.Recommended for steel, stainless
3,03,0steel and cast iron.

For all materials. 2,0 0 0,05 0,10 0,15 0,25 0,30 Feed fn (mm/rot.) 0 0,10 0,20 0,30 0,40 0,50

Feed fn (mm/rot.)

GP…02-MMRadial feedAxial feedRecommended starting value.
Inserts Width (mm)Cutting Depth (ap), mmFor cutting speed recommendations, see page D-693
Width (W) [mm]ap [mm]
8,05,0
W=8mmMedium Multi Function
4,0W=5mm(Grooving & Turning)
5,0W=4mm
3,0W=3mmFor grooving and turning in all

4,0 materials. 2,0 3,0 Good chip control. 1,0

0 0,05 0,10 0,15 0,25 0,30 0 0,10 0,15 0,20 0,25 0,30 0,35 0,40 Feed fn (mm/rot.) Feed fn (mm/rot.)

GP…02-MP

Radial feed Axial feed Inserts Width (mm) Cutting Depth (ap), mm ap [mm] Width (W) [mm] 5,0 Medium Profiling W=6mm 4,0 For profiling all materials.

6,0 3,0 Outstanding chip control even at

2,0 low feeds and small depths of cut. 1,0 Good surface finish. 0 0,10 0,20 0,30 0,40 0,50 0 0,20 0,25 0,30 0,35 0,40 0,45 0,50 0,55 0,60

Feed fn (mm/rot.) Feed fn (mm/rot.)

GP…02-NP

Radial feed Axial feed Inserts Width (mm) Cutting Depth (ap), mm

Width (W) [mm] ap [mm] Medium Aluminium profiling

5,0 W=8mm 8,0 First choice for profiling in 4,0

W=6mm non-ferrous materials. 3,0

Good chip flow provides a better

6,0 2,0 surface finishing.

1,0 Sharp cutting edge. 0 0,10 0,20 0,30 0,40 0,50 0 0,20 0,25 0,30 0,35 0,40 0,45 0,50 0,55 0,60 Feed fn (mm/rot.) Feed fn (mm/rot.)