Общий каталог Palbit - страница 38

Предыдущая страница Следующая страница

Навигация

SEHW | SEHT

A SPARE PARTS | A

Complementos | Repuestos

= Ar45ºbor Mp=+19º ountingdg Dc2 Dc dL ap
Order code Código Reference Referência ReferenciaDimensi ØDcnsDime ØDc2nsõesØdimensiones Ødg(mm) LKgSpeci Arbor Typeications Ap max (mm)Insert Pastilha InsertoStock
181003500 050A06045-04-19-U022040450622242400,350A6,0SE...T/W 1204
181148800 063A06045-05-19-022050563752242500,800A6,0SE...T/W 1204
181148900 080A06045-06-19-027050680922750501,150A6,0SE...T/W 1204
181149000 100A06045-06-19-03205061001123264501,700A6,0SE...T/W 1204
181040200 125A06045-07-19-U04006371251324085632,750B6,0SE...T/W 1204
181040300 160A06045-08-19-U040063816017240100634,600C6,0SE...T/W 1204
Insert ScrewKey (Torx)KeyTorque Value
Cutter
ØDc
Nm
Nm
A06045 – 50 - 160P0501100PT20DT20505,0

Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Check the procedures for the clamping screws on the page A-243. Grades selection guide | Guia para selecção de graus | Tabla para selección de calidades

HB Wear Resistance Toughness

4SS - Ferritic / Martensitic200-330✓
M5SS - Austenitic200-330✓

Good Conditions

9Nodular cast iron160-250Average Conditions
N10Aluminium and Non Ferrous30-130✓Difficult Conditions

Stock item | Produto de stock | Itens de stock Available under request (see page A-6) | Disponível sobre consulta (consulte a página A-6) | Disponible bajo consulta (mire pagina A-6) recommended cutting conditions | Condições de corte recomendadas | Condiciones de corte recomendables

ISOPSMMaterialHB (Brinell)Wear ResisVc (m/min) tanceToughnessFeed fz (mm/t)
PH0910PH6920PH6740SEHT 1204…SEHT 1204 LNSEHW 1204…
1Unalloyed Steel125-220-150-230130-1600,10-0,20-0,10-0,20
P2Low-Alloyed Steel220-280-140-220120-1500,10-0,20-0,10-0,20
3High-Alloyed Steel280-380-130-180100-1300,10-0,20-0,10-0,20
4SS - Ferritic/Martensitic200-330--100-1200,10-0,15-0,10-0,20
M5SS - Austenitic200-330--80-1100,10-0,15-0,10-0,20
6SS - Austenitic-ferritic(Duplex)230-260--70-1000,10-0,15-0,10-0,20
7Malleable Cast Iron130-230-150-280130-2500,10-0,25-0,10-0,25
K8GreyCast Iron180-245-130-230110-2200,10-0,25-0,10-0,25
9Nodular Cast iron160-250-80-19080-1700,10-0,25-0,10-0,25
N10Aluminium and Non Ferrous30-130350-1400---0,10-0,25-

4

R 5

PMKNSHDimensions
CVDPVDCVDPVDCVDPVDUNC PCDPVDPVDDimensões

Dimensiones

S (Note 1) Cutting conditions ae/DC=70% (Note 2) Cutting conditions should be ajusted according to the machine and work rigidity. (Note 3) If chattering occurs, reduce ap and Vc by 30% and keep the same fz per thooth

CHIP-BREAKER selection guide |

Guia para aplicações do quebra-aparas | Guía para aplicación del rompevirutas

ISOPSMMaterialHB (Brinell)Chip-Breaker 1st choiseApplication Dificult Operations
1Unalloyed Steel125-220SEHT 12... AFENSEHW 12... AFEN
P2Low-Alloyed Steel220-280SEHT 12... AFTNSEHW 12... AFTN
3High-Alloyed Steel280-380SEHT 12... AFTNSEHW 12... AFTN
4SS - Ferritic/Martensitic200-330SEHT 12... AFENSEHW 12... AFEN
M5SS - Austenitic200-330SEHT 12... AFENSEHW 12... AFEN
6SS - Austenitic-ferritic(Duplex)230-260SEHW 12... AFEN-
7Malleable Cast Iron130-230SEHT 12... AFENSEHW 12... AFEN
K8GreyCast Iron180-245SEHT 12... AFENSEHW 12... AFEN
9Nodular Cast iron160-250SEHW 12... AFENSEHW 12... AFTN
N10Aluminium and Non Ferrous30-130SEHT 12... AFFN-LN-

(1)

code Reference iC S I F B R

1110222 SEHW 1204 AFTN 12,70 4,76 12,70 2,80 - -