Общий каталог Palbit - страница 49

d Key DIN 6368

	Insert Screw	Key (Torx)	(Torx - Nm) Torque Value		Wrench Screw
	Cutter
	ØDc
			Nm
				Nm
A06815 - 63-80	P0501302	PT20	DT2050	5,0	- -
A06815 - 100	P0501302	PT20	DT2050	5,0	J0123510 SD6368-12
A06815 – 125	P0501302	PT20	DT2050	5,0	J0164110 SD6368-16
A06815 – 160	P0501302	PT20	DT2050	5,0	- -
Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Arbor Mounting
Check the procedures for the clamping screws on the page A-243.

=15º | =+2º | =4,5 Dc

p Rp

Order code Código	Reference Referência Referencia		Dimensio ØDc	ns	Dimensõ Ød/M	es	Dimension Ødg	es (mm) L	Kg	Specifica Ap max ()	tions Arbor T	Insert Pastilha Inserto	Stock
181100400	063A06815-05-02-027050	5	63	27	48	50	0,460	mm 3,50	ype A	SO...1605...
181081900	066A06815-05-02-027050	5	66	27	48	50	0,500	3,50	A	SO...1605...
181082000	080A06815-06-02-027050	6	80	27	60	50	0,900	3,50	A	SO...1605...
181082100	100A06815-08-02-032050	8	100	32	80	50	1,600	3,50	B	SO...1605...
181082200	125A06815-10-02-040063	10	125	40	90	63	2,900	3,50	B	SO...1605...
181082300	160A06815-12-02-U040063	12	160	40	110	63	4,400	3,50	C	SO...1605...

			HB	Wear Resi	stance	Grades		Toughness
ISO	PSM	Material	(Brinell)	PH7910	PH7920	PH7930	PH7740	PHM740
	1	Unalloyed Steel	125-220	✓	✓	✓	✓
P	2	Low-Alloyed Steel	220-280	✓	✓	✓	✓
	3	High-Alloyed Steel	280-380	✓	✓	✓	✓
	4	SS - Ferritic/Martensitic	200-330			✓	✓	✓
M	5	SS - Austenitic	200-330			✓	✓	✓
	6	SS - Austenitic-ferritic(Duplex)	230-260			✓	✓	✓
	7	Malleable Cast Iron	130-230	✓	✓		✓		Good Conditions
K	8	GreyCast Iron	180-245	✓	✓		✓
	9	Nodular Cast iron	160-250	✓	✓		✓		Average Conditions
S	11	Heat Resistant Super Alloys	200-320			✓	✓	✓	Difficult Conditions

SOEW SOEW F ° 3 1 R recommended cutting conditions | Condições de corte recomendadas | Condiciones de corte recomendables

ISO	PSM	Material	HB (Brinell)	Wear Re	sistance	Vc (m/min)	To	ughness	Feed fz	(mm/t)
				PH7910	PH7920	PH7930	PH7740	PHM740	SOEW 16...	SOET 16…
	1	Unalloyed Steel	125-220	160-280	150-230	140-220	100-180	-	0,60-2,50	0,50-2,20
P	2	Low-Alloyed Steel	220-280	150-230	140-220	130-180	90-170	-	0,60-2,50	0,50-2,20
	3	High-Alloyed Steel	280-380	140-190	130-180	100-170	80-140	-	0,60-2,00	0,50-1,80
	4	SS - Ferritic/Martensitic	200-330	-	-	130-220	100-180	100-180	-	0,60-2,00
M	5	SS - Austenitic	200-330	-	-	120-180	90-150	90-150	-	0,60-2,20
	6	SS - Austenitic-ferritic(Duplex)	230-260	-	-	70-140	70-120	70-120	-	0,50-1,80
	7	Malleable Cast Iron	130-230	160-350	150-310	-	120-260	-	0,60-2,50	0,50-2,00
K	8	GreyCast Iron	180-245	150-300	140-260	-	130-220	-	0,60-2,50	0,50-2,00
	9	Nodular Cast iron	160-250	120-260	100-220	-	100-180	-	0,60-2,00	0,50-1,80
S	11	Heat Resistant Super Alloys	200-320	-	-	35-65	25-60	25-60	-	0,40-1,80

SOET

		CVD	PVD	CVD PVD	CVD	PVD	UNC PCD CVD PVD	PVD		Dimensões	(Note 1) Cutting conditions ae/Dc=70%.
									Dimensiones
	(2) Grade code	T9 P7 G1 G4 P3 G6 R1 P3 G6 L5 L6 G1 G4 P3 G6 10 D6 R1 P3 G6 P7								(mm)	(Note 2) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases:
												- When using long shank;
(1)												- When using long tool overhang with arbor type;

Geometry ISO - When application has poor clamping rigidity or when using a low rigidity machine.

code	Reference	iC	S	I	R	F
							(Note 3) PH5… and PHS… can be used wet or dry. PH7… use only air.
1111907 SOEW 160512 S		16,40 5,26		-	1,20 1,50
							(Note 4) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases:
1112221 SOET 160520-MS		16,40 5,26		-	2,00	-		- When using long shank;

- When using long tool overhang with arbor type;

Отправьте заявку