Общий каталог Palbit - страница 97

TOROMILL x2 35190 TOROMILL X2 35190

RNHX

Complementos | Repuestos Guia para aplicações do quebra-aparas | Guía para aplicación del rompevirutas

Order separately HB Chip-Breaker Application

Insert Screw Key (Torx) Key Torque Value ISO PSM Material

(Torx - Nm) (Brinell) 1st choise Dificult Operations

Cutter

ØDc 1 Unalloyed Steel 125-220 LP MP

Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243.

Check the procedures for the clamping screws on the page A-243. M	5	SS - Austenitic	200-330	LP	-
	6	SS - Austenitic-ferritic (Duplex)	230-260	LP	MP
	7	Malleable Cast Iron	130-230	MP	-
K	8	Grey Cast Iron	180-245	MP	-
	9	Nodular Cast iron	160-250	MP	-
S	11	Heat Resistant Super Alloys	200-320	LP	-

Guia para selecção de graus | Tabla para selección de calidades Descida em rampa | Bajada en rampa Grades HB Wear Resistance Toughness

ISO PSM Material (Brinell)

PH7920 PH7930 PHM740 Ramping Lr

	1	Unalloyed Steel	125-220	✓	✓
P	2	Low-Alloyed Steel	220-280	✓	✓
	3	High-Alloyed Steel	280-380	✓	✓
	4	SS - Ferritic / Martensitic	200-330		✓	✓
M	5	SS - Austenitic	200-330		✓	✓
	6	SS - Austenitic-ferritic (Duplex)	230-260		✓	✓

Good Conditions

	7	Malleable Cast Iron	130-230	✓
K	8	Grey Cast Iron	180-245		Average Conditions

	9	Nodular Cast iron	160-250	✓			Difficult Conditions
S	11	Heat Resistant Super Alloys	200-320		✓	✓

Ramping

recommended cutting conditions | Insert ØDc

Max Ramp aº Max ap Min Lr

Condições de corte recomendadas | Condiciones de corte recomendables

	32	1	3	171,9
Vc (m/min)	40	0,8	3	214,8

HB RNHX… 12

ISO PSM Material (Brinell) Wear Resistance Toughness

42 0,8 3 214,8

PH7920 PH7930 PHM740 fz (mm/t) ap (mm) RNHX 1204

	1	Unalloyed Steel	125-220	150-230		130-210		-	0,15-0,50	0,50-3,00	50	0,8	3	214,8
P	2	Low-Alloyed Steel	220-280	140-220		120-200		-	0,15-0,50	0,50-3,00	63	0,6	3	286,5
	3	High-Alloyed Steel	280-380	130-180		110-160		-	0,15-0,50	0,50-3,00
	4	SS - Ferritic / Martensitic	200-330		-	100-120	100-130		0,10-0,35	0,50-3,00	80	0,5	3	343,8
M	5	SS - Austenitic	200-330		-	80-110	80-120		0,10-0,35	0,50-3,00
	6	SS - Austenitic-ferritic (Duplex)	230-260		-	70-100	70-110		0,10-0,35	0,50-3,00
	7	Malleable Cast Iron	130-230		-	150-280		-	0,15-0,55	0,50-3,00
K	8	Grey Cast Iron	180-245		-	130-230		-	0,15-0,55	0,50-3,00
	9	Nodular Cast iron	160-250		-	80-190		-	0,15-0,55	0,50-3,00
S	11	Heat Resistant Super Alloys	200-320		-	20-80	20-90		0,05-0,30	0,50-3,00