Общий каталог Palbit - страница 73

Предыдущая страница Следующая страница

Навигация

A LNXT 0904... | grades selection guide | A

Inserts | Pastilhas | Plaquitas Guia para selecção de graus | Tabla para selección de calidades

HBWear ResisGra tancedesToughness
ISOPSMMaterial(Brinell)PH5320PH7920PHS740PH7740
1Unalloyed Steel125-220✓✓
P2Low-Alloyed Steel220-280✓✓
3High-Alloyed Steel280-380✓✓
4SS - Ferritic / Martensitic200-330✓
M5SS - Austenitic200-330✓
6SS - Austenitic-ferritic (Duplex)230-260✓
7Malleable Cast Iron130-230✓✓✓Good Conditions
K8Grey Cast Iron180-245✓✓✓Average Conditions
9Nodular Cast iron160-250✓✓✓Difficult Conditions

F R

iC S

Dimensiones

Geometry ISO

codeReferenceiCSIRF
1112225 LNXT 090404 PNER-MP-4,59,00,4-
1112226 LNXT 090408 PNER-MP-4,59,00,8-

First choice | Primeira opção | 1ª opción Stock item | Produto de stock | Itens de stock Available under request (see page A-7) | Disponível sobre consulta Insert order code = (1) Geometry Code + (2) Grade Code recommended cutting conditions |

(consulte a página A-7) | Disponible bajo consulta (mire pagina A-7) Condições de corte recomendadas | Condiciones de corte recomendables

ISOPSMMaterialHB (Brinell)Wear ResistanVc (m ce/min)ToughnessFeed fz (mm/t)
PH5320PH7920PHS740PH7740LNXT 09… MP
1Unalloyed Steel125-220-180-250140-170-0,08-0,25
P2Low-Alloyed Steel220-280-170-210130-160-0,08-0,25
3High-Alloyed Steel280-380-160-200110-140-0,08-0,15
4SS - Ferritic / Martensitic200-330---120-1800,08-0,25
M5SS - Austenitic200-330---100-1500,08-0,20
6SS - Austenitic-ferritic (Duplex)230-260---70-1300,08-0,15
7Malleable Cast Iron130-230180-320170-300-160-2700,08-0,30
K8Grey Cast Iron180-245160-270150-250-140-2300,08-0,25
9Nodular Cast iron160-250100-23090-210-90-2000,08-0,20

Complementos | Repuestos

K Order separately
It SK TeyT Vl
nser crewey orxorque aue
Torx - Nm
Cutter ØDcNmNm
E90090 - 25-32P0250700XT07DT07091,2
W90090 - 16-32P0250700XT07DT07091,2
A90090 - 40-63P0250700XT07DT07091,2
R90090 - 25-32P0250700XT07DT07091,2

(Note 1) Cutting conditions ae/Dc=70%. Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Check the procedures for the clamping screws on the page A-243. (Note 2) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine.