Общий каталог Palbit - страница 65

Предыдущая страница Следующая страница

Навигация

A spare parts | grades selection guide | A

Complementos | Repuestos Guia para selecção de graus | Tabla para selección de calidades Order separately Grades

Insert ScrewKey (Torx)Key (Torx - Nm)Torque Value
Cutter ØDcNmNm
E20090 - 10P0180300XT06IPDT0606IP0,6
E20090 - 12-16P0180400XT06IPDT0606IP0,6
R20090 - 12-16P0180400XT06IPDT0606IP0,6

Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Check the procedures for the clamping screws on the page A-243.

recommended cutting conditions |

Condições de corte recomendadas | Condiciones de corte recomendables

4SS - Ferritic / Martensitic200-330✓
M5SS - Austenitic200-330✓
6SS - Austenitic-ferritic (Duplex)230-260✓
7Malleable Cast Iron130-230✓✓
K8Grey Cast Iron180-245✓✓
9Nodular Cast iron160-250✓✓
Good Conditions
N10Aluminium and Non Ferrous30-130✓
S11Heat Resistant Super Alloys200-320Average Conditions
H12Hardened Steels40-55 HRC✓Difficult Conditions
ISO PSM MaterialHB (Brinell)Wear ResistanceVc (m/min)ToughnessFeed fz (mm/t)
PH7603PH0910PH7910PH7920PH7930XPET 06...LPXPET 06...LNXPET 06...HFXPHW 06...MH
1 Unalloyed Steel125-220220-280-200-260180-240160-2200,05-0,07-0,40-0,80,05-0,12
P 2 Low-Alloyed Steel220-280210-290-190-270170-250150-2300,05-0,07-0,40-0,80,05-0,12
3 High-Alloyed Steel280-380200-240-180-230160-210140-1900,05-0,07-0,40-0,60,05-0,12
4 SS - Ferritic/Martensitic200-330----130-2200,05-0,07-0,40-0,8-
M 5 SS - Austenitic200-330----120-1800,05-0,07-0,40-0,6-
6 SS - Austenitic-ferritic(Duplex)230-260----70-1400,05-0,07-0,40-0,6-
7 Malleable Cast Iron130-230---160-350160-3500,05-0,07-0,50-0,8-
K 8 GreyCast Iron180-245---150-320150-3000,05-0,07-0,50-0,8-
9 Nodular Cast iron160-250---130-280120-2600,05-0,07-0,50-0,8-
N 10 Aluminium and Non Ferrous30-130-350-1400----0,05-0,07--
S 11 Heat Resistant Super Alloys200-320----35-650,05-0,07-0,40-0,6-
H 12 Hardened Steels40-55 HRC120-260-------0,03-0,10

(Note 1) Cutting conditions ae/Dc=70%. (Note 2) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine. (Note 3) PH5… and PHS… can be used wet or dry. PH7… use only air. (Note 4) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine.

Operation Slottingae 100%Vc & fzap (mm) 1,0-3,0
Shouldering≤25%>8% >12%1,0-4,0 1,0-4,0