Общий каталог Palbit - страница 61

Предыдущая страница Следующая страница

Навигация

AANHX 1206.. |grades selection guide |A
Inserts | Pastilhas | PlaquitasGuia para selecção de graus | Tabla para selección de calidades
ANHX-LS | MPGrades

ANHX-LS ANHX-MP NEW

(PHS grade) HB Wear Resistance Toughness

ISO PSM Material (Brinell)

PH5320 PH7920 PH7930 PHS740 PH7740

1Unalloyed Steel125-220✓✓✓✓
P2Low-Alloyed Steel220-280✓✓✓✓
3High-Alloyed Steel280-380✓✓✓✓
4SS - Ferritic / Martensitic200-330✓✓
M5SS - Austenitic200-330✓✓

P M K N S H Dimensions

Dimensões 6 SS - Austenitic-ferritic (Duplex) 230-260 ✓ ✓

CVD PVD CVD PVD CVD PVD UNC PCD PVD PVD

Dimensiones 7 Malleable Cast Iron 130-230 ✓ ✓ ✓

(2) Grade code T9 P7 G1 G4 P3 G6 R1 P3 G6 L5 L6 L9 G1 G4 P3 G6 10 D6 P3 G6 P7 (mm) Good Conditions

K8Grey Cast Iron180-245✓✓✓
(1)9Nodular Cast iron160-250Average Conditions
GeometryISOS11Heat Resistant Super Alloys200-320
ReferenceiCSIRF✓✓Difficult Conditions
code
1112474 ANHX 120604 PNER-LS9,0 8,3 12,0 0,4 1,6
1112237 ANHX 120608 PNER-LS9,0 8,3 12,0 0,8 1,2
CHIP-BREAKER selection guide |
1112429 ANHX 120616 PNER-LS9,0 8,3 12,0 1,6 0,4Guia de selecção do quebra-aparas | Guía de selección del rompevirutas
1112473 ANHX 120604 PNSR-MP9,0 8,3 12,0 0,4 1,6Chip Breaker Application
ISOPSMMaterialHB (Brinell)Chip Breaker 1stchoiceApplication Difficult Operations
1Unalloyed Steel125-220ANHX 12… LSANHX 12… MP
P2Low-Alloyed Steel220-280ANHX 12… MP-
3High-Alloyed Steel280-380ANHX 12… MP-
4SS - Ferritic / Martensitic200-330ANHX 12… LS-
M5SS - Austenitic200-330ANHX 12… LS-
6SS - Austenitic-ferritic (Duplex)220-260ANHX 12… LS-
7Malleable Cast Iron130-230ANHX 12… LSANHX 12… MP
K8Grey Cast Iron180-245ANHX 12… MP-
9Nodular Cast iron160-250ANHX 12… MP-
S11Heat Resistant Super Alloys200-320ANHX 12… LS-

1112430 ANHX 120616 PNSR-MP 9,0 8,3 12,0 1,6 0,4

First choice | Primeira opção | 1ª opción Stock item | Produto de stock | Itens de stock Available under request (see page A-7) | Disponível sobre consulta Insert order code = (1) Geometry Code + (2) Grade Code

Condições de corte recomendadas | Condiciones de corte recomendables

ISOPSMMaterialHB (Brinell)Wear ResistanceVc (m/min)ToughnessFeed fz(mm/t)
PH5320PH7920PH7930PHS740PH7740ANHX 12… LSANHX 12… MP
1Unalloyed Steel125-220-150-230150-180130-160130-1600,10-0,200,10-0,30
P2Low-Alloyed Steel220-280-140-220140-170120-150120-1500,10-0,200,10-0,25
3High-Alloyed Steel280-380-130-180120-150100-130100-1300,10-0,150,10-0,20
4SS - Ferritic / Martensitic200-330--90-150-100-1200,10-0,20-
M5SS - Austenitic200-330--80-130-80-1100,10-0,15-
6SS - Austenitic-ferritic (Duplex)230-260--70-100-70-1000,10-0,15-
7Malleable Cast Iron130-230170-300150-280--130-2500,10-0,250,10-0,30
K8Grey Cast Iron180-245150-250130-230--100-2000,10-0,250,10-0,30
9Nodular Cast iron160-25090-21080-190--50-1500,10-0,200,10-0,25
S11Heat Resistant Super Alloys200-320--25-100-20-800,07-0,10-

(Note 1) Cutting conditions ae/Dc=70%. (Note 2)

OperationaeVc & fzap (mm)
Slotting100%<20%2.5-4.0
<50%>8%4,0-7,0
Shouldering
≤25%>12%7,0-10,0

(Note 3) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type;

- When application has poor clamping rigidity or when using a low rigidity machine.

PLUNGING |

DR S max.

Smax = DC.Dr - Dr2

S max and DR corresponding cutting diameter Dc (mm) Dc (mm) DR (mm)

3240506380100125
1,05,66,27,07,98,99,911,1
2,07,78,79,811,012,514,015,7
3,09,310,511,913,415,217,119,1