Общий каталог Palbit - страница 47

Общий каталог Palbit 2022

A Grades selection guide | CHIP-BREAKER selection guide | A

Guia para selecção de graus | Tabla para selección de calidades Guia para aplicações do quebra-aparas | Guía para aplicación del rompevirutas

Grades HB Chip-Breaker Application

ISO PSM Material

(Brinell) 1st choise Dificult Operations

HB Wear Resistance Toughness

ISO PSM Material (Brinell)

				PH7910	PH7920	PH7930	PH7740	PHM740		1	Unalloyed Steel	125-220	SOET 13...	SOEW 13…
									P	2	Low-Alloyed Steel	220-280	SOEW 13...		-
	1	Unalloyed Steel	125-220	✓	✓	✓	✓			3	High-Alloyed Steel	280-380	SOEW 13...		-
P	2	Low-Alloyed Steel	220-280	✓	✓	✓	✓			4	SS - Ferritic / Martensitic	200-330	SOET 13...		-
	3	High-Alloyed Steel	280-380	✓	✓	✓	✓		M	5	SS - Austenitic	200-330	SOET 13...		-
	4	SS - Ferritic / Martensitic	200-330				✓	✓		6	SS - Austenitic-ferritic (Duplex)	230-260	SOET 13...		-
M	5	SS - Austenitic	200-330				✓	✓		7	Malleable Cast Iron	130-230	SOET 13...	SOEW 13...
	6	SS - Austenitic-ferritic (Duplex)	230-260				✓	✓	K	8	Grey Cast Iron	180-245	SOEW 13...		-
	7	Malleable Cast Iron	130-230	✓	✓		✓			9	Nodular Cast iron	160-250	SOEW 13...		-
K	8	Grey Cast Iron	180-245	✓	✓		✓		S	11	Heat Resistant Super Alloys	200-320	SOET 13...		-

Good Conditions

9 Nodular Cast iron 160-250 ✓ ✓ ✓

Average Conditions

S 11 Heat Resistant Super Alloys 200-320 ✓ ✓ ✓

Difficult Conditions

recommended cutting conditions | PROGRAMMING DATA |

Condições de corte recomendadas | Condiciones de corte recomendables Dados para programação | Datos para la programación Vc (m/min) Programming Data HB Feed fz (mm/t)

ISO PSM Material Wear Resistance Toughness Insert

(Brinell)

Rp X b ae

PH7910 PH7920 PH7930 PH7740 PHM740 SOEW 13... SOET 13…

SO… 13M5.. 2,5 1,1 10,5 10,0

	1	Unalloyed Steel	125-220	160-280		150-230		140-220		100-180		-	0,50-2,20		0,50-2,00
P	2	Low-Alloyed Steel	220-280	150-230		140-220		130-180		90-170		-	0,50-2,20		b 0,50-2,00
	3	High-Alloyed Steel	280-380	140-190		130-180		100-170		80-140		-	0,50-2,00		0,50-1,80
	4	SS - Ferritic / Martensitic	200-330		-		-	130-220		100-180	100-180			-	0,50-1,80
M	5	SS - Austenitic	200-330		-		-	120-180		90-150	90-150			-	0,50-1,80
	6	SS - Austenitic-ferritic (Duplex)	230-260		-		-	70-140		70-120	70-120			-	0,50-1,50
	7	Malleable Cast Iron	130-230	160-350		150-310			-	120-240		-	0,50-2,20		0,50-2,00
K	8	Grey Cast Iron	180-245	150-300		140-260			-	100-200		-	0,50-2,20		0,50-2,00
	9	Nodular Cast iron	160-250	120-260		100-220			-	80-150		-	0,50-2,20		0,50-1,80
S	11	Heat Resistant Super Alloys	200-320		-		-	35-65		25-60	25-60			-	0,40-1,30

(Note 1) Cutting conditions ae/Dc=70%. (Note 2) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine. (Note 3) PH5… and PHS… can be used wet or dry. PH7… use only air. (Note 4) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine.

Rp ae

Общий каталог Palbit - страница 47

Навигация

recommended cutting conditions | PROGRAMMING DATA |

Отправьте заявку

На подбор необходимой оснастки и оборудования