Общий каталог Palbit - страница 43

Предыдущая страница Следующая страница

Навигация

PENTA HIFEED 06320 PENTA HIFEED 06320

POKT

A SPARE PARTS RAMPING AND HELICAL INTERPOLATION A

Complementos | Repuestos

Order separatelyOrder separately
Insert ScrewKey (Torx)Key (Torx - Nm)Torque ValueScrewDIN 6368 Wrench
Cutter ØDcNmNm
R06320 - 16-42P0250503XT08DT08121,20--
E06320 - 25-40P0250503XT08DT08121,20--
A06320 - 40-60P0250503XT08DT08121,20--

Interpolation

Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Check the procedures for the clamping screws on the page A-243.

Grades selection guide |

Guia para selecção de graus | Tabla para selección de calidades Grades HB Wear Resistance Toughness

ISO PSM Material

(Brinell)PH7910PH7920PH7930PH7740
1Unalloyed Steel125-220✓✓

Dc

Blind hole Flat bottom

Ødi = ØDH - ØDc

ØDcMax Ramp aºRamping Max apMin LrØDHminHelical Interpolation ØDHmaxMax Pitch/Rev.
16151,03,723,4 -- 30,06 11
209,01,06,331,4 -- 38,05 8
255,01,011,441,4 -- 48,04 6
323,41,016,855,4 -- 62,04 5
353,01,019,161,4 -- 68,04 5
402,01,028,671,4 -- 78,03 4
422,01,028,684,0 -- 82,04 4
502,01,028,691,4 -- 98,04 5
522,01,028,695,4 -- 102,04 5
632,01,028,6117,4 -- 124,05 6
661,81,031,8123,4 -- 130,05 6

K 8 Grey Cast Iron 180-245

ISOPSMMaterialHB (Brinell)Wear ResistanVc (m ce/min)ToughnessFeed fz (mm/t)
PH7910PH7920PH7930PH7740POKT 04...-MP
1Unalloyed Steel125-220190-280180-250--0,50-1,50
P2Low-Alloyed Steel220-280180-240170-210--0,50-1,50
3High-Alloyed Steel280-380170-220160-200--0,50-1,50
4SS - Ferritic/Martensitic200-330--130-170120-1800,50-1,40
M5SS - Austenitic200-330--100-160100-1500,50-1,40
6SS - Austenitic-ferritic(Duplex)230-260--80-14070-1300,50-1,40
7Malleable Cast Iron130-230180-320170-300--0,50-1,50
K8GreyCast Iron180-245170-280150-250--0,50-1,50
9Nodular Cast iron160-250100-24090-210--0,50-1,50
S11Heat Resistant Super Alloys200-320--30-7530-700,50-1,30

Note: During helical interpolation do not exceed max Pitch.

L≤3Dc L>3Dc S

(Note 1) Cutting conditions ae/Dc=70%. (Note 2) It’s possible to occur vibrations in certain cases. Please reduce depth of cut and / or reduce cutting conditions in following cases: - When using long shank; - When using long tool overhang with arbor type; - When application has poor clamping rigidity or when using a low rigidity machine. (Note 3) PH5… and PHS… can be used wet or dry. PH7… use only air.

SmaxandDRcorrsponding c Dcutting diamete (mm) POKT 0r Dc (mm) 4...
DR (mm)1620253235404250526366
1,03,94,44,95,75,86,26,47,07,17,98,1
2,05,36,06,82,78,18,78,99,810,011,011,3
3,06,27,18,19,39,810,510,811,912,113,413,7
4,06,98,09,210,611,112,012,313,613,915,415,7

PROGRAMMING DATA |

Insert

RpXbae
POKT 0403...2,51,24,34,0