Общий каталог Palbit - страница 103

Общий каталог Palbit - страница 103

LINEPRO 40095 | 40595 | 41095 LINEPRO 40095 | 40595 | 41095

LINEPRO 40095 | 40595 | 41095 LINEPRO 40095 | 40595 | 41095

Отправьте заявку

Навигация

На подбор необходимой оснастки и оборудования

Общий каталог Palbit 2022

XDHW

Insert Screw Key (Torx) Key

Ramping	Lr		ap Helical Interpolation	D	H Pitch
		Dc	Blind hole Flat bottom
Insert ØDc XDHW 04 10	Max Ramp aº 7,3	Ramping Max ap 0,8	Min Lr ØDHmin 6,2 18,0 -	Helical Interpo ØDHmax - 20,0	lation Max Pitch/Rev. 3,2 4,0 Ødi = ØDH - ØDc
… 12	5,3	0,8	8,6 22,0 -	- 24,0	2,9 3,5
16	8	1,0	7,1 30,0 -	- 32,0	6,2 7,1
XDHW 06… 20	5,7	1,0	10,0 38,0 -	- 40,0	5,6 6,3
25	4	1,0	14,3 48,0 -	- 50,0	5,1 5,5
25	8,7	1,0	6,5 48,0 -	- 50,0	11,1 12,0
35	5,2	1,0	11,0 68,0 -	- 70,0	9,4 10,0
42	4	1,0	14,3 82,0 -	- 84,0	8,8 9,2
XDHW 10… 52	3	1,0	19,1 102,0 -	- 104,0	8,2 8,6
66	2,3	1,0	24,9 130,0 -	- 132,0	8,1 8,3
80	1,8	1,0	31,8 158,0 -	- 160,0	7,7 7,9

Cutter ØDc Nm

R41095 – 10 - 12	P0180401	XT06	DT0606	0,6		-
R40095 – 16 - 25	P0250503	XT08	DT0812	1,2		-
R40595 – 25 - 42	P0350800	XT15	DT1530	3,0		-
C40595 – 52 - 80	P0350800	XT15	DT1530	3,0	P0350750

Note: The toolholder is supplied with the XT/PT key. To order the DT key please check the page A-243. Check the procedures for the clamping screws on the page A-243.

Grades HB Wear Resistance Toughness (Brinell) PHD103 PH6103 PH6910 PH6125 PH6135 PDP410 PBH910

K	8	Grey Cast Iron	180-245	✓
N	10	Aluminium and Non Ferrous	30-130		Average Conditions

ISO	PSM	Material	HB (Brinell)	Wear Res	istance	Vc (m/min)	T	oughness	PCD	PCBN
				PHD103	PH6103	PH6910	PH6125	PH6135	PDP410	PBH910
	1	Unalloyed Steel	125-220	-	180-300	180-250	160-190	150-180	-	-
P	2	Low-Alloyed Steel	220-280	-	180-250	170-210	140-180	140-170	-	-
	3	High-Alloyed Steel	280-380	-	180-230	160-200	130-160	120-150	-	-
	7	Malleable Cast Iron	130-230	-	-	170-300	160-290	-	-	-
K	8	GreyCast Iron	180-245	-	-	150-250	140-240	-	-	-
	9	Nodular Cast iron	160-250	-	-	90-210	80-200	-	-	-
N	10	Aluminium and Non Ferrous	30-130	300-1000	-	-	-	-	800-3000	-
H	12	Hardened Steels	40-55 HRC	-	120-260	-	-	-	-	200-600

Insert	Feed fz Rouhin	(mm/t) Finishin	ap Rec.
XD… 04	gg 0.10-0.20	g 0.10-0.15	0.1-0.5
XD… 06	0.15-0.30	0.10-0.25	0.2-0.8
XD… 10	0.15-0.35	0.10-0.30	0.2-0.8

(Note 1) Cutting conditions should be ajusted according to the machine and work rigidity. (Note 2) If chattering occurs, reduce ap and Vc by 30% and keep the same fz per thooth

SPARE PARTS |

RAMPING AND HELICAL INTERPOLATION

Complementos | Repuestos

Descida em rampa e interpolação helicoidal | Bajada en rampa e interpolación circular

Order separately

Order separately