Каталог Sumitomo пластины с алмазными вставками Sumidia - страница 39
Навигация
Каталог Sumitomo токарные резцы (державки) для внутреннего точения
Каталог Sumitomo микроинструмент
Техническая информация Sumitomo
Каталог Sumitomo модульные системы для револьверных головок токарных станков
Каталог Sumitomo твердосплавные заготовки
Каталог Sumitomo фрезы со сменными пластинами
SRFAluminium Alloy Milling Cutter
Radial −2° to ＋4° 5 P M K N N S H Type
＋ Steel Stainless Steel Cast Iron Non-Ferrous Metal Aluminium Exotic Alloy Hardened Steel
| Axial | 6° | H | H | H | S | G | H | H | |||
| High-speed Finishing for Non-Ferrous Metal | |||||||||||
| Fig 1 | Fig 2 | Fig 3 | Fig 4 |
40 60
38 20 BT30 6
100 26 6
60 （刃先とボルト 13 (12) 23
頭部間距離） 50 45
- Body
Inch Adjustment Screw Dimensions (mm) SRFJ
Diameter Boss No. of Weight
Cat. No. Stock Fig
DC DCSFMS teeth (kg) Insert Screw
SRF 30R-ST D Q BFTX0409N
| 30 | 3 | 1 | 0.34 | ||||
| 40R-ST | D | 40 | Q | 4 | 1 | 0.50 | |
| SRF 30R-BT30 | D | 30 | Q | 3 | 2 | 0.57 | |
| 40R-BT30 | D | 40 | Q | 4 | 2 | 0.72 | |
| SRF 30R | D | 30 | 50.0 | 3 | 3 | 0.27 | |
| 40R | D | 40 | 50.0 | 4 | 3 | 0.35 | |
| 50R | D | 50 | 46.5 | 5 | 4 | 0.59 | |
| 63R | D | 63 | 45.0 | 6 | 4 | 0.67 |
Inserts are not included. Please use hexagonal bolt (JISB1176) M12 x 30-35 mm for securing ø50 and ø63 cutter to the arbor.
- Inserts
- Parts
Wiper Insert Side View
| Fig 5 | Fig 6 | Fig 7 | (Same For All) | Insert Screw | Adjustment Screw | Wrenches | ||
| 9.525 | 9.555 | 9.525 | 3.962 | TH015 |
C0.5 C0.5 R0.5
| 6 | 6 | 6 | ||
| R100 | ||||
| N m |
| BFTX0409N 4.0 | SRFJ | TTX15W | ||||
| Recommended Tightening Torque（N・m） | ||||||
| P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel | N m | |||||
| Grade | SUMIDIA |
| High Speed/Light | N | N | ■ Maximum Depth Of Cut Guide (SRF50R, 5 Teeth) | |||
| Application | General Purpose | N | N | |||
| The table below contains guidelines on the maximum depth of cut determined from | ||||||
| Roughing | N | N | S |
internal tests. ' ' marks indicate the possible application range. Actual cutting Cutting conditions should be set based on actual machine and work characteristics. Cat. No. Fig Edge Feed Rate v (mm/min)
f
NF-SNEW 09T3ADTR D F Feed
| 5 | Standard | 2,500 | 4,000 | 5,000 | |
| Rate |
09T3ADTR-U D F Depth of Cut Feed Rate Per Tooth f (mm/t)
| 6 | Wiper | z | |
| a (mm) |
D F p 0.05 0.08 0.10
09T3ADTR-R 7 Nose Radius
0.5 S S S
- Standard inserts and wiper inserts can be used on the same cutter body.
| 1.0 | S | S | S | |
| ● Inserts with nose radius can reduce the clattering. | S | S | S | |
| 1.5 | ||||
| These cannot be used with wiper inserts. | S | S | S |
(22) 2.0 M
| ● Inserts can be reground 3 times (up to minimum | 2.5 | S | S | S | |
| 12 | |||||
| IC diameter 9.225mm). | 1 3.0 | S | S | S | |
| ● | 3.5 | S | S | Q | |
| Do not mix new and reground inserts, or | |||||
| 4.0 | S | Q | Q | ||
| even inserts with different regrind amount | |||||
| 4.5 | S | Q | Q | ||
| on the same cutter. | |||||
| 45° 5.0 | S | Q | Q |
- When using reground inserts, it is advisable to SUMIDIA
SUMIDIA Binderless re-confirm insert height and cutting Cutting Conditions (4 Equi-spaced Holes) 4 M5 x 0.8 Depth 8 SUMICRYSTAL diameter with a tool pre-setter. Cutter: SRF50R
- Arbor for SRF30R, SRF40R Insert: NF-SNEW 09T3ADTR (DA1000)
= 10,000min-1 ø40±0.2 Arbor: BT30 FMA25.4-45 When using SRF30R and SRF40R cutters, there is a requirement to modify the arbor as Work: A-5052 shown above. Width: 35mm at depth of cut indicated above (1. Reduce part of the arbor's adaptor shaft from ø25.4mm to ø15mm. 2. Add 4 tap holes for (M5) cap screws.) Please use a hexagonal bolt M5 × 20 mm for securing the body.