Общий каталог ZCC-CT 2019

Каталог ZCC-CT сверла со сменными пластинами

Каталог ZCC-CT сверла монолитные

Каталог ZCC-CT оснастка

Каталог ZCC-CT расточные системы

Каталог ZCC-CT фрезы со сменными пластинами

Каталог ZCC-CT фрезы монолитные

A End mill – GM series

				p		GM- GM- GM- St	2BL 4BL 2BFP arting valu	es for cu	tting spee	GM GM d vc [m/m	-2R -4R in]
			Bill	grou					Slot m	illing	Shoulde	r milling
Material group	Composition / struc	ture / heat treatment	rne hardness HB	ning					Ø [mm]	ap max	Ø [mm]	ae max
				achi					0 < x < 3	0,1 x D	0 < x ≤ 20	< 0,5 x D
				M					3 ≤ x ≤ 20	0,8 x D
						KMG	303			KMG	303
						ae	/ D			ae	/ D
					1/1	1/10	1/20	f-group	1/1	1/2	1/10	f-group
	approx. 0,15 % C	annealed	125	1		220	250	5	160	215	275	2
	approx. 0,45 % C	annealed	190	2		210	240	5	155	205	265	2
Unalloyed steel	approx. 0,45 % C	tempered	250	3		155	175	5	115	155	195	2
	approx. 0,75 % C	annealed	270	4		135	150	5	100	130	165	2
	approx. 0,75 % C	tempered	300	5		125	140	5	90	120	155	2
P		annealed	180	6		165	190	5	120	165	210	2
Low-alloyed steel		tempered	275	7		135	150	5	100	130	165	2
		tempered	300	8		125	140	5	90	120	155	2
		tempered	350	9		115	130	5	85	115	145	2
High-alloyed steel and high-alloyed		annealed	200	10		155	175	5	115	155	195	2
tool steel		hardened and tempere	325 d	11		120	135	5	85	115	150	2
	ferritic/martensitic	annealed	200	12		75	80	5	55	70	90	2
	martensitic	tempered	240	13		65	70	5	45	65	80	2
M Stainless steel	austenitic	quench hardened	180	14		75	85	5	55	75	95	2
	austenitic-ferritic		230	15		65	70	5	45	65	80	2
Grey cast iron	perlitic/ferritic		180	16		165	185	5	120	160	205	2
	perlitic (martensitic)		260	17		135	150	5	100	130	165	2
	ferritic		160	18		200	225	5	145	195	250	2
K Cast iron with spheroidal graphite
	perlitic		250	19		155	175	5	115	155	195	2
Malleable cast iron	ferritic		130	20		220	250	5	160	215	275	2
	perlitic		230	21		180	200	5	130	175	220	2
	cannot be hardened		60	22
Aluminium wrought alloys
	hardenable	hardened	100	23
	≤ 12 % Si, cannot be hardened		75	24
N Cast aluminium alloys	≤ 12 % Si, hardenable	hardened	90	25
	> 12 % Si, cannot be hardened		130	26
	machining steel, PB> 1%		110	27
Copper and copper alloys (bronze/brass)	CuZn, CuSnZn		90	28
	CuSn, Pb-free copper, electrol	ytic copper	100	29
		annealed	200	30
	Fe-based alloys
		hardened	280	31
Heat-resistant alloys		annealed	250	32
S	Ni or Co bass	hardened	350	33
		cast	320	34
	pure titanium		Rm400	35
Titanium alloys	α and β alloys	hardened	Rm1050	36
Hardened steel		hardened and tempere hardened and tempere	55 HRC 60 HRC d d	37 38
H Hard cast iron		cast	400	39
Hardened cast iron		hardened and tempere	55 HRC d	40
	Thermoplasts			41
	Thermosetting plastics			42
	Plastic, glass-fibre reinforced G	i FRP		43
X Non-metallic materials	Plastic, carbon fibre reinforced	i CFRP		44
	Graphite Wood			45 46

Note: The given cutting values are guide values, which were determined under ideal conditions. The values have to be adapted in individual cases. Feed rate recommendations on page B460.

Общий каталог ZCC-CT 2019 - страница 905

Навигация

A End mill – GM series

Общий каталог ZCC-CT 2019 - страница 905

Навигация

A End mill – GM series

Отправьте заявку

На подбор необходимой оснастки и оборудования