Каталог Sumitomo токарные резцы (державки) для внутреннего точения - страница 78

Предыдущая страница Следующая страница

Навигация

BNBX / BNB

SUMIBORON

BNBX Holders

Dimensions (mm)

GradesMin. machining Diameter Height LengthNose
diameterradiusApplicable
Internal / FacingCat. No.

BN2000 BN7000 BN700 DMIN DCON H LF RE Sleeves

BNBX 020RDDF2.52.01.8400.2HBX 2016
BNBX 025RDDF3.02.52.2400.2HBX 2516
Min. machinable diameter DMIN BNBX 030RDDF
3.53.02.7400.2HBX 3016
DCON 3°DDF
BNBX 035R4.03.53.2400.2HBX 3516
BNBX 040RDDF4.54.03.7400.2HBX 4016
H BNBX 045RDDF5.04.54.2400.2HBX 4516
RE
LF BNBX 050RDDF
5.55.04.7600.2HBX 5016
BNBX 055RDDF6.05.55.2600.2HBX 5516
BNBX 060RDDF6.56.05.7600.2HBX 6016
BNBX 065RD7.06.56.2600.2HBB 6516
BNBX 070RD7.57.06.7800.2HBB 716
BNBX 075RD8.07.57.2800.2HBB 7516
BNBX 080RD8.58.07.7800.2HBB 816

E Sleeves Parts (For Sleeve)

Hole BT06035T TRD TH

Cat. No. StockDiameterApplicable Tools
DCB
HBX 2016D2.0BNBX 020R
DCB(For Torx
HBX 2516D2.5BNBX 025Rholes) BT0404
HBX 3016D3.0BNBX 030R
Applicable
15 15 HBX 3516DWrenches Set screws Screw
3.5BNBX 035Rsleeves
100 HBX 4016D
4.0BNBX 040R
HBX 4516D4.5BNBX 045R1.5 HBX2SSS
HBX 5016D5.0BNBX 050R
HBX 5516DTRD15 BT06035T BFTX0409N HBX3SSS
5.5BNBX 055R
DHBX4SSS
HBX 60166.0BNBX 060RSSS 3.0
DHBX5
DCB ø16 HBB 65166.5BNBX 065RSSS
HBX6
HBB 716D7.0BNBX 070R
HBB 7516D7.5BNBX 075RSSSS Q Q
TH020 BT0404 HBB
100 15 HBB 816D
8.0BNBX 080R
Note: BNBX type tools may also be installed in HBB type sleeves, but HBX type sleeves are recommended for tools with diameters less than ø6 mm.
DMIN Min.
BNBmachinable diameter■ Parts

DCON 2° Internal / Facing

  • Holders

This figure shows right H LF handed tools. GAMF Dimensions (mm)

Min. machining Diameter Height Length Rake angle

Cat. No. Stock diameter Clamp Bolts Nuts Wrench

DMINDCONHLFGAMF
BNB 508RD10.08.07.0140− 9BH0306 BNBW-2
BNB 510RD12.010.09.0140− 8
BNB 512RD14.012.011.0160− 6TH020 BNBC FBUP3-A0-9 BNBW-4
BNB 516RD18.016.014.0180− 5
BNB 520RD22.020.018.0180− 4BH0310 BNBW-7
  • Inserts (SUMIBORON, SUMIDIA)
GradesDimensions*1 TBGN -BSTN is an item
60°(mm)
1.59
limited to BNX20 with
SUMIBORONSUMIDIA

ø3.97 5° different negative land angle.

(BSTN: -15 , B: -25 ) Note that the negative 5° land angle is set differently for each grade.

Cat. No. *2 NF-TBGN is a 1-corner design.

TBGN 060102BDDDD(All surfaces are not
0.2
SUMIDIA)
TBGN 060104BDDDDDDFDD0.4
TBGN 060108BDDDDDF0.8
TBGN 060102-BSTN*1QDQQQQQQQ0.2
TBGN 060104-BSTN*1QDQQQQQQQ0.4
TBGN 060108-BSTN*1QDQQQQQQQ0.8
NF-TBGN 060102*2QQQQQQQQD0.2
NF-TBGN 060104*2QQQQQQQQD0.4