Каталог Sumitomo токарные резцы (державки) для внутреннего точения - страница 35
Навигация
Каталог Sumitomo монолитные фрезы
Каталог Sumitomo твердосплавные заготовки
Каталог Sumitomo токарные резцы (державки) для наружного точения
Каталог Sumitomo пластины с кубическим нитридом бора Sumiboron
Общий каталог Sumitomo 2019 - 2020- E001
- E002
- E003
- E004
- E005
- E006
- E007
- E008
- E009
- E010
- E011
- E012
- E013
- E014
- E015
- E016
- E017
- E018
- E019
- E020
- E021
- E022
- E023
- E024
- E025
- E026
- E027
- E028
- E029
- E030
- E031
- E032
- E033
- E034
- E035
- E036
- E037
- E038
- E039
- E040
- E041
- E042
- E043
- E044
- E045
- E046
- E047
- E048
- E049
- E050
- E051
- E052
- E053
- E054
- E055
- E056
- E057
- E058
- E059
- E060
- E061
- E062
- E063
- E064
- E065
- E066
- E067
- E068
- E069
- E070
- E071
- E072
- E073
- E074
- E075
- E076
- E077
- E078
- E079
- E080
- E081
- E082
S-DDQN / S-DDUN / D-DDUN
107.5°
Profiling
- Inserts
S-DDQN DMIN Min.
Steel machinable diameter DCON
Profiling 107.5° ・DNMG150408N-GE (Representative example)
H LF –12°
Parts
– 6° LH This figure shows right handed tools.
- Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts. Dimensions (mm)
Holder Conventional Cat. Stock Min. machining DiameterHeight Length Cutting edge Head Offset Applicable inserts Clamp Wrench for Wrench for
Cat. No. diameter distance
| Material | No. | R L DMIN DCON H LF WF LH E1 | Cat. No. | Page | set | upper surface lower surface | ||
| S32T-DDQN R/L1504-40 | D D | □□ | SS From |
| Steel | S32T-DDQN R/L15 | 40 | 32 | 30 300 22 | 48 | 6 DN | 1504 | SCP-2 | 5.0 | LH040 | LH025 | ||||||
| B32 | |||||||||||||||||
| Parts for clamp set | E81 E | ||||||||||||||||
| S-DDUN | Fig 1 | DMIN Min. | Fig 2 | DMIN Min. | |||||||||||||
| Steel | machinable diameter | DCON | machinable diameter | DCON |
Profiling 93° 93°
H H LF LF -12° : -6° -6° LH
Parts
This figure shows right handed tools.
- Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts. Dimensions (mm)
Stock Min. machining Cutting edge Head Applicable inserts
Holder Diameter Height Length Offset Clamp Screw for Wrench for Wrench for
Cat. No. diameter distance Fig Shim
Material R L DMIN DCON H LF WF LH E1 Cat. No. Page set shim upper surface lower surface
S32S-DDUN R/L1504-40 D D 40 32 30 250 22.0 26 7.0
D D 1 SS From
| S40T-DDUN R/L1504-50 | 50 | 40 | 37 300 27.0 26 8.5 | DN□□ 1504 | SCP-2 | 5.0 | DNS1504B BFTX0409N LH040 LH025 | |||||||||
| B32 | ||||||||||||||||
| S50U-DDUN R/L1504-63 | D D | 63 | 50 | 47 350 31.5 | Q | 8.0 | 2 | |||||||||
| Parts for clamp set | E81 | |||||||||||||||
| D-DDUN | Steel with | DMIN Min. | ■ Inserts |
vibration DCON control machinable diameter mechanism Profiling Oil hole
93° ・DNMG110404N-GU ・DNMG150604N-GE H (Representative LF GU type GE type example) GAMF – 6°
Parts
LH
This figure shows right handed tools.
- Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts. Dimensions (mm)
Stock Min. machining Height Length Cutting edge Head Rake Applicable inserts
Holder Diameter angle Clamp Screws Wrenches for Wrenches for
Cat. No. diameter distance Shims
| Material | R L DMIN DCON H LF WF LH GAMF | Cat. No. | Page | sets | for shim upper surface lower surface | |||
| D32T-DDUN R/L1104-40 | D D | − | □□ | SS From |
| 40 | 32 | 30 300 22 | 26 | 10 DN | 1104 | SCP-1 | 5.0 | DNS1104B BFTX0307N LH040 LH025 | |||||
| B31 | |||||||||||||
| D32T-DDUN R/L1506-40 | D D | 40 | 32 | 30 300 22 | 26 | − 12 | From | ||||||
| DN □□ 1506SS | SCP-2 | 5.0 | DNS1506B BFTX0409N LH040 LH025 | ||||||||||
| D40U-DDUN R/L1506-50 | D D | 50 | 40 | 37 350 27 | 26 | − 12 | B36 |
Parts for clamp set E81