Каталог Sumitomo токарные резцы (державки) для внутреннего точения - страница 26
Навигация
Каталог Sumitomo монолитные фрезы
Каталог Sumitomo твердосплавные заготовки
Каталог Sumitomo токарные резцы (державки) для наружного точения
Каталог Sumitomo пластины с кубическим нитридом бора Sumiboron
Общий каталог Sumitomo 2019 - 2020- E001
- E002
- E003
- E004
- E005
- E006
- E007
- E008
- E009
- E010
- E011
- E012
- E013
- E014
- E015
- E016
- E017
- E018
- E019
- E020
- E021
- E022
- E023
- E024
- E025
- E026
- E027
- E028
- E029
- E030
- E031
- E032
- E033
- E034
- E035
- E036
- E037
- E038
- E039
- E040
- E041
- E042
- E043
- E044
- E045
- E046
- E047
- E048
- E049
- E050
- E051
- E052
- E053
- E054
- E055
- E056
- E057
- E058
- E059
- E060
- E061
- E062
- E063
- E064
- E065
- E066
- E067
- E068
- E069
- E070
- E071
- E072
- E073
- E074
- E075
- E076
- E077
- E078
- E079
- E080
- E081
- E082
D-DWLN / S-PWLN
General Boring
- Inserts
| D-DWLN | Steel with | DMIN Min. | ||
| vibration | DCON | |||
| control | machinable diameter | |||
| mechanism | ||||
| Bottom Facing | Oil hole | 95° |
・WNMG080408N-GE H (Representative example) LF GAMF
- Parts
– 6° LH This figure shows right handed tools.
- Holders The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.) Dimensions (mm)
Holder Stock Min. machining Height Length Cutting edge Head Rake Applicable inserts Wrench Wrench
Diameter angle Clamp Screws
Cat. No. diameter distance Shims for upper for lower
Material R L DMIN DCON H LF WF LH GAMF Cat. No. Page set for shim surface surface
| D25T-DWLN R/L0804-32 | D D | 32 | 25 | 23 300 17 | 26 | − | WNS0803B BFTX0307N | ||
| Vibration | 12 | ||||||||
| E control | D32T-DWLN R/L0804-40 | D D | − | SS From □□ | |||||
| mechanism | 40 | 32 | 30 300 22 | 26 | 10 WN | 0804 SCP-2 | LH040 LH025 5.0 | ||
| B71 | WNS0804B BFTX0409N | ||||||||
| Steel with D40U-DWLN R/L0804-50 | D D | − | |||||||
| oil hole | 50 | 40 | 37 350 27 | 26 | 10 | ||||
| E81 Parts for clamp set | |||||||||
| S-PWLN | DMIN Min. | ■ Inserts |
Steel machinable diameter DCON
Bottom Facing 95° ・WNMG080408N-GE H (Representative example) LF
GAMF -6°
- Parts
LH
This figure shows right handed tools.
- Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts;
Holders left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts. Dimensions (mm)
Holder Stock Min. machining DiameterHeight Length Cutting edge Head Rake Applicable inserts Lever Shim
Cat. No. diameter distance angle Bolts Shims Wrenches
| Material | R | L DMIN DCON H LF WF LH GAMF | Cat. No. | Page | pins | retainers | |||
| S32S-PWLN R/L0604-40 | D | D | − | □□ | SS From |
| 40 | 32 | 30 250 22 | 29 | 10 WN | 0604 | LCL3 LCS3 LSW317 LSP3 LH025 | ||||
| B69 | ||||||||||
| S32S-PWLN R/L0804-40 | D | D | 40 | 32 | 30 250 22 | 29 | −10 | |||
| □□ | SS From | |||||||||
| D | D | − | WN 0804 | LCL4 LCS4 LSW42B LSP4 LH030 | ||||||
| S40T-PWLN R/L0804-50 | 50 | 40 | 37 300 27 | 29 | 10 | B71 |
Note: About Applicable Inserts for DWLN Type and PWLN Type For internal machining: Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts; left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts. For facing: Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts; left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.