Каталог Sumitomo резьбонарезной инструмент - страница 23

Предыдущая страница Следующая страница

Навигация

LTE Type

LTE Type Standard Depth of Cut

■ Without Wiper Edge

ApplicationCat. No.Reference Cat. No.Nose RPitchDepth of cut Number of Passes1 2 345 6789 10 1112 1314
1.00 mm0.6550.20 0.16 0.120.100.07
1.250.8460.20 0.18 0.160.130.10 0.07
TME 1020R16ER 102060-TE0.131.501.0370.22 0.20 0.170.150.12 0.100.07
ving1.751.2280.22 0.21 0.180.160.15 0.130.100.07
groo2.001.41100.22 0.20 0.180.160.14 0.130.120.100.09 0.07
rnal1.50 mm0.9570.22 0.17 0.140.130.12 0.100.07
Exte1.751.1480.22 0.18 0.160.150.14 0.120.100.07
TME 1530R16ER 153060-TE0.202.001.3390.25 0.20 0.180.160.15 0.130.100.090.07
ead2.501.71120.25 0.22 0.190.170.15 0.140.130.120.10 0.09 0.080.07
ic thr3.002.09140.25 0.22 0.200.200.18 0.170.150.140.14 0.10 0.100.09 0.080.07
metr1.00 mm0.5960.16 0.12 0.100.080.08 0.05
60`°`1.250.7570.16 0.14 0.120.100.10 0.080.05
TMI 1020R16IR 102060-TI0.061.500.9280.18 0.15 0.140.120.10 0.100.080.05
ving1.751.0890.18 0.16 0.140.130.12 0.120.100.080.05
groo2.001.24100.20 0.18 0.150.140.12 0.120.100.100.08 0.05
rnal1.50 mm0.9180.18 0.14 0.140.120.10 0.100.080.05
Inte1.751.0790.18 0.16 0.130.130.12 0.120.100.080.05
TMI 1530R16IR 153060-TI0.092.001.23100.20 0.18 0.140.140.12 0.120.100.100.08 0.05
2.501.56120.20 0.18 0.160.160.15 0.130.130.110.11 0.10 0.080.05
3.001.88140.22 0.20 0.180.180.16 0.160.140.140.10 0.10 0.100.08 0.070.05
20 threads/inch0.8060.20 0.17 0.150.120.09 0.07
d190.8460.20 0.18 0.160.130.10 0.07
hrea vingTWE 2416R16ER 241655-TE0.13180.9070.20 0.18 0.150.120.10 0.080.07
rth t groo161.0370.22 0.20 0.170.150.12 0.100.07
itwo rnal14 threads/inch1.0780.20 0.17 0.150.140.13 0.120.090.07
5`°`W Exte121.2990.22 0.20 0.170.150.14 0.130.120.090.07
5TWE 1410R16ER 141055-TE0.23111.43100.22 0.21 0.180.160.14 0.130.120.110.09 0.07
101.60110.22 0.21 0.180.170.16 0.140.130.120.11 0.09 0.07

Grooving

Cut-Off

Threading

Note: The smaller the pitch, the lower you should set the cutting speed. Also, for internal diameter without a wiper edge, set the number of passes higher.

■ SumiGrip LTE Type Holder Shim Selection

T＝3° (Shim LSTESS-2) T＝2° (Shim LSTESS-1)

Nonmachinable D D

areas 4.0 T 3° T 2° 3.0

T 1° SS (Standard shim LSTE -0) 2.0

1.0

Effective thread diameter (mm)

A-A cross-section Screw groove

T A A Insert T Shim

Lead angle LTE type comes with β = 1° shim in its standard parts. β° = 2° and 3° shim are sold separately. Additionally, STE and STI types do not have shim.