Основной каталог Kyocera 2021 - 2022 - страница 919

Предыдущая страница Следующая страница

Навигация

Recommended cutting conditions

Toolholder description and feed rate (fz: mm/t)Recommended insertgrades ( Vc: m/min)
ert type Workpiece materialMEGACOAT NANOCVD Coated carbide
InsMFH...R-10-...MFH...R-14-...
PR1535PR1525PR1510CA6535
Carbon steel0.5~1.5~2.0✩ 120~180~250★ 120~180~250--
Alloy steel0.5~1.5~2.0✩ 100~160~220★ 100~160~220--
Mold steel (~ 40HRC)0.5~1.2~1.8✩ 80~140~180★ 80~140~180--
Mold steel (40 ~ 50HRC)0.2~0.7~1.0✩ 60~100~130★ 60~100~130--
Stainless steel (Austenitic related)0.5~1.2~1.8✩ 100~160~200✩ 100~160~200--
GM GH Stainless steel (Martensitic related)0.5~1.2~1.8✩ 150~200~250--★ 180~240~300
Stainless steel (Precipitation hardening)0.5~1.2~1.8★ 90~120~150---
Gray cast iron0.5~1.5~2.0--★ 120~180~250-
Nodular cast iron0.5~1.2~1.8--★ 100~150~200-
Ni-base heat-resistant alloys0.2~0.8~1.2✩ 20~30~50--★ 20~30~50
Titanium alloys0.2~0.8~1.2★ 40~60~80-☆ 30~50~70-
Carbon steel0.5~1.5~2.0(ap≤1.0mm) 0.06~0.2~0.3(ap≤3.5mm)0.5~1.5~2.0(ap≤2.0mm) 0.06~0.2~0.4(ap≤5.0mm)✩ 120~180~250★ 120~180~250--
Alloy steel0.5~1.5~2.0(ap≤1.0mm) 0.06~0.2~0.3(ap≤3.5mm)0.5~1.5~2.0(ap≤2.0mm) 0.06~0.2~0.4(ap≤5.0mm)✩ 100~160~220★ 100~160~220--
Mold steel (~ 40HRC)0.5~1.2~1.8(ap≤1.0mm) 0.06~0.15~0.2(ap≤3.5mm)0.5~1.2~1.8(ap≤2.0mm) 0.06~0.15~0.3(ap≤5.0mm)✩ 80~140~180★ 80~140~180--
Mold steel (40 ~ 50HRC)0.2~0.7~1.0(ap≤1.0mm) 0.03~0.1~0.15(ap≤3.5mm)0.2~0.7~1.0(ap≤2.0mm) 0.03~0.1~0.2(ap≤5.0mm)✩ 60~100~130★ 60~100~130--
Stainless steel (Austenitic related)0.5~1.2~1.8(ap≤1.0mm) 0.06~0.15~0.2(ap≤3.5mm)0.5~1.2~1.8(ap≤2.0mm) 0.06~0.15~0.3(ap≤5.0mm)★ 100~160~200✩ 100~160~200--
LD Stainless steel (Martensitic related)0.5~1.2~1.8(ap≤1.0mm) 0.06~0.15~0.2(ap≤3.5mm)0.5~1.2~1.8(ap≤2.0mm) 0.06~0.15~0.3(ap≤5.0mm)✩ 150~200~250--★ 180~240~300
Stainless steel (Precipitation hardening)0.5~1.2~1.8(ap≤1.0mm) 0.06~0.15~0.2(ap≤3.5mm)0.5~1.2~1.8(ap≤2.0mm) 0.06~0.15~0.3(ap≤5.0mm)★ 90~120~150---
Gray cast iron0.5~1.5~2.0(ap≤1.0mm) 0.06~0.2~0.3(ap≤3.5mm)0.5~1.5~2.0(ap≤2.0mm) 0.06~0.2~0.4(ap≤5.0mm)--★ 120~180~250-
Nodular cast iron0.5~1.2~1.8(ap≤1.0mm) 0.06~0.15~0.2(ap≤3.5mm)0.5~1.2~1.8(ap≤2.0mm) 0.06~0.15~0.3(ap≤5.0mm)--★ 100~150~200-
Ni-base heat-resistant alloys0.2~0.8~1.2(ap≤1.0mm) 0.03~0.1~0.15(ap≤3.5mm)0.2~0.8~1.2(ap≤2.0mm) 0.03~0.1~0.2(ap≤5.0mm)✩ 20~30~50--★ 20~30~50
Titanium alloys0.2~0.8~1.2(ap≤1.0mm) 0.03~0.1~0.15(ap≤3.5mm)0.2~0.8~1.2(ap≤2.0mm) 0.03~0.1~0.2(ap≤5.0mm)★ 40~60~80-✩ 30~50~70-
Carbon steel0.5~1.5~2.0✩ 120~180~250★ 120~180~250--
Alloy steel0.5~1.5~2.0✩ 100~160~220★ 100~160~220--
Mold steel (~ 40HRC)0.5~1.2~1.8✩ 80~140~180★ 80~140~180--
Mold steel (40 ~ 50HRC)0.2~0.7~1.0✩ 60~100~130★ 60~100~130--
Stainless steel (Austenitic related)0.5~1.2~1.8★ 100~160~200✩ 100~160~200--
FL Stainless steel (Martensitic related)0.5~1.2~1.8✩ 150~200~250--★ 180~240~300
Stainless steel (Precipitation hardening)0.5~1.2~1.8★ 90~120~150---
Gray cast iron0.5~1.5~2.0--★ 120~180~250-
Nodular cast iron0.5~1.2~1.8--★ 100~150~200-
Ni-base heat-resistant alloys0.2~0.8~1.2✩ 20~30~50--★ 20~30~50
Titanium alloys0.2~0.8~1.2★ 40~60~80-✩ 30~50~70-
  • Machining with coolant is recommended for Ni-base heat-resistant alloys and titanium alloys. ★: 1st Recommendation ✩: 2nd Recommendation
  • The bold-faced number indicates a center value of recommended cutting condition. Adjust the cutting speed and the feed rate within the above conditions according to the actual machining situation.
  • When finishing with LD type and FL type inserts, recommended feed rate for SOMT14 LD type: f=1.5(mm/rev) or less/for SOMT10 LD type: f=0.9(mm/rev) or less

for SOMT14 FL type: f=3.0(mm/rev) or less/for SOMT10 FL type: f=1.4(mm/rev) or less

  • For machining center equivalent to BT30, reduce feed rate to 25% or less of the recommended condition.
  • For slotting, internal coolant is recommended.