Основной каталог Kyocera 2021 - 2022 - страница 596

Предыдущая страница Следующая страница

Навигация

Carbon steel / Alloy steelPQPP
Stainless steelPPQM
Cast ironK
Non-ferrous metalsQPN
Dimension (mm)Angle (°)ToleranceCarbide
PVD-

Insert Description Applicable toolholder

CW S RE INSL PSIR& CW min. CW max.

GDM 1316N-003PF 0.03 N N N

2 1.3 16 - 0.04 + 0.04

1316N-015PF0.15N N N
GDM 1516N-003PF3.70.03

2 1.5 16 - 0.04 + 0.04 N N N

1516N-015PF0.15N N N
REGDM 2020N-003PF0.03N N N

INSL RE 2 2 20 - - 0.04 + 0.04

2020N-015PF0.15N N N
GDM 2520N-003PF0.03N N N

Low feed 2 2.5 4.3 20 - 0.04 + 0.04

2520N-015PF0.15N N N
GDM 3020N-003PF0.03N N N

2 3 20 - 0.04 + 0.04

3020N-015PF0.15N N N
HGDM 1316L-003PF-15DN N N
21.30.0316- 0.04+ 0.04
1316R-003PF-15DN N N

GDM 1516L-003PF-15D 3.7 0.03 N N N

1516R-003PF-15D21.50.0316- 0.04+ 0.04N N N
1516R-015PF-15D0.15N N N
GDM 2020L-003PF-15D0.03N N N
PSIRR
RE2020R-003PF-15D220.0320- 0.04+ 0.04N N N
INSL15
2020R-015PF-15D0.15N N N
Low feedGDM 2520L-003PF-15D0.03N N N
2520R-003PF-15D22.54.3 0.0320- 0.04+ 0.04N N N
2520R-015PF-15D0.15N N N
GDM 3020L-003PF-15D0.03H22, H23, H25, H26,
N N N
H27, H28
3020R-003PF-15D230.0320- 0.04+ 0.04N N N
3020R-015PF-15D0.15N N N
GDM 2020N-010PQ220.120- 0.03+ 0.03NNN
RE
REGDM 2520N-010PQ22.54.3 0.120- - 0.03+ 0.03NNN
INSLINSL
GDM 3020N-010PQ230.120- 0.03+ 0.03NNN
GDM 2020R-010PQ-15D 220.120- 0.03+ 0.03NNN
PSIRR
INSL REGDM 2520R-010PQ-15D 22.54.3 0.12015 - 0.03+ 0.03NNN
GDM 3020R-010PQ-15D 230.120- 0.03+ 0.03NNN
GDG 2020N-005PG220.0520- 0.02+ 0.02NNN N
RE
INSL CW 3° REGDG 2520N-005PG22.54.3 0.0520- - 0.02+ 0.02NNN N
Low cutting forceGDG 3020N-005PG230.0520- 0.02+ 0.02NNN N
GDG 2020R-005PG-15D 220.0520- 0.02+ 0.02NNN N
PSIRR
RE
INSLGDG 2520R-005PG-15D 22.54.3 0.052015 - 0.02+ 0.02NNN N
Low cutting forceGDG 3020R-005PG-15D 230.0520- 0.02+ 0.02NNN N

Using the PF / PM chipbreaker (for cut-off) for grooving cannot create a flat bottom (Ref. to the right figure). Groove bottom created by PF / PM chipbreaker