Основной каталог Kyocera 2021 - 2022

Каталог Kyocera пластины с CVD покрытием для обработки чугуна

Каталог Kyocera пластины TQ для нарезания резьбы c прессованным стружколомом

Каталог Kyocera высокопроизводительные модульные сверла DRA

Каталог Kyocera фрезы MRX с позитивными круглыми пластинами

Каталог Kyocera пластины с CVD покрытием для обработки стали

Spare parts

Clamp screw	Description	Wrench	Description	Tightening torque (N·m)
	HS-2524TRP HS-2534TRP HS-3048TRP HS-4067TRP	DTP FTP	FTP-5 DTP-6 DTP-7	0.5 0.8 1.2

Recommended cutting conditions

General purpose GM / Cast iron KM

Workpiece material	Recommen grade (m/m	ded insert s / Vc in)	n (min -1)			Drill dia.	DC (mm)
	PR1535	PR1525	f (mm/rev)	ø8	ø11	ø14	ø18	ø22	ø25
			n (min -1)	3,980 - 7,160	2,890 - 5,210	2,270 - 4,090	1,770 - 3,180	1,450 - 2,600	1,270 - 2,290
Low carbon steel	100 - 180	100 - 180	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.4	0.2 - 0.45	0.2 - 0.45
M			n (min -1)	3,980 - 5,970	2,890 - 4,340	2,270 - 3,410	1,770 - 2,650	1,450 - 2,170	1,270 - 1,910
Carbon steel ose G	100 - 150	100 - 150	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.4	0.2 - 0.45	0.2 - 0.45
purp			n (min -1)	2,790 - 4,780	2,030 - 3,470	1,590 - 2,730	1,240 - 2,120	1,010 - 1,740	890 - 1,530
Alloy steel eral	70 - 120	70 - 120	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.4	0.2 - 0.45	0.2 - 0.45
Gen			n (min -1)	1,990 - 3,580	1,450 - 2,600	1,140 - 2,050	880 - 1,590	720 - 1,300	640 - 1,150
Mold steel	50 - 90	50 - 90	f (mm/rev)	0.08 - 0.17	0.08 - 0.22	0.11 - 0.25	0.11 - 0.28	0.14 - 0.32	0.14 - 0.32
			n (min -1)	1,590 - 2,790	1,160 - 2,030	910 - 1,590	710 - 1,240	580 - 1,010	510 - 890
Stainless steel				0.1 - 0.24	0.1 - 0.24	0.12 - 0.3	0.15 - 0.3	0.15 - 0.3	0.15 - 0.35
	40 70	40 70
	-	-	f (mm/rev)		Feed rate 0.15 mm	/rev or less is recomme	nded until drillingdep	th reaches 0.5 x DC
			n (min -1)	3,580 - 6,760	2,600 - 4,920	2,050 - 3,870	1,590 - 3,010	1,300 - 2,460	1,150 - 2,170
Gray cast iron	90 - 170	90 - 170	f (mm/rev)	0.14 - 0.29	0.14 - 0.37	0.19 - 0.43	0.19 - 0.45	0.24 - 0.45	0.24 - 0.45
			n (min -1)	1,590 - 4,780	1,160 - 3,470	910 - 2,730	710 - 2,120	580 - 1,740	510 - 1,530
Nodular cast iron	40 - 120	40 - 120	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.4	0.2 - 0.45	0.2 - 0.45
G i		90 170	n (min -1)	3,580 - 6,760	2,600 - 4,920	2,050 - 3,870	1,590 - 3,010	1,300 - 2,460	1,150 - 2,170
ray cast ron on	-	-	f (mm/rev)	0.17 - 0.35	0.19 - 0.42	0.23 - 0.53	0.25 - 0.60	0.32 - 0.60	0.32 - 0.60
Ndlti st ir KM		40 120	n (min -1)	1,590 - 4,780	1,160 - 3,470	910 - 2,730	710 - 2,120	580 - 1,740	510 - 1,530
ouar cas ron Ca	-	-	f (mm/rev)	0.12 - 0.24	0.17 - 0.36	0.21 - 0.48	0.24 - 0.60	0.27 - 0.60	0.27 - 0.60

Recommended cutting conditions above is for 1.5D/3D type. As drilling depth increases (1.5D/3D 5D 8D 12D), feed rates should be reduced. Recommended feed rate : 1.5/3D type=100%, 5D type=80% or less :1st recommendation :2nd recommendation Recommended cutting speed and feed rate: 8D type=80% or less, 12D type=70% or less General Purpose GM.

Counterboring FTP

Workpiece material	Recommen grade (m/	ded insert s / Vc min)	n (min -1)			Drill dia.	DC (mm)
	PR1535	PR1525	f (mm/rev)	ø8	ø11	ø14	ø18	ø22	ø25
b l			n (min -1)	3,150 - 6,000	2,300 - 4,350	1,800 - 3,400	1,400 - 2,650	1,150 - 2,200	1,000 - 1,900
Low caron stee	80 - 150	80 - 150	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.40	0.20 - 0.45	0.20 - 0.45
			n (min -1)	3,150 - 4,750	2,300 - 3,450	1,800 - 2,700	1,400 - 2,100	1,150 - 1,750	1,000 - 1,500
TP Carbon steel	80 - 120	80 - 120	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.40	0.20 - 0.45	0.20 - 0.45
ing F ll l			n (min -1)	2,800 - 4,750	2,000 - 3,450	1,600 - 2,700	1,250 - 2,100	1,000 - 1,750	900 - 1,500
erbor Aoy stee	70 - 120	70 - 120	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.40	0.20 - 0.40	0.20 - 0.45
ount			n (min -1)	1,600 - 2,800	1,150 - 2,000	900 - 1,600	700 - 1,250	600 - 1,000	500 - 900
C Mold steel	40 - 70	40 - 70	f (mm/rev)	0.08 - 0.17	0.08 - 0.22	0.11 - 0.25	0.11 - 0.28	0.14 - 0.30	0.14 - 0.32
			n (min -1)	1,600 - 2,800	1,150 - 2,000	900 - 1,600	700 - 1,250	600 - 1,000	500 - 900
Stainless steel				010 - 020	010 - 020	010 - 024	015 - 024	015 - 024	015 - 028
	40 - 70	40 - 70	f (mm/rev)	. .	. .	. .	. .	. .	. .
					Feed rate 0.15 mm	/rev or less is recomm	ended until drillingde	pth reaches 0.5 x DC
			n (min -1)	2,800 - 5,600	2,000 - 4,050	1,600 - 3,200	1,250 - 2,500	1,000 - 2,000	900 - 1,800
Gray cast iron	70 - 140	70 - 140	f (mm/rev)	0.14 - 0.29	0.14 - 0.37	0.19 - 0.43	0.19 - 0.45	0.24 - 0.45	0.24 - 0.45
			n (min -1)	1,600 - 4,000	1,150 - 2,900	900 - 2,750	700 - 1,750	600 - 1,450	500 - 1,250
Nodular cast iron	40 - 100	40 - 100	f (mm/rev)	0.12 - 0.24	0.12 - 0.31	0.16 - 0.36	0.16 - 0.40	0.2 - 0.45	0.2 - 0.45

* The recommended cutting conditions are for drilling on plain surface :1st recommendation :2nd recommendation The conditions for drilling on slant hole shows the depth from the top of workpiece Set the feed rate 50% or under when inclination angle is 30 or under. Set the feed rate 30% or under when inclination angle is over 30° Traversing is not recommented. Applicable to 1.5D,3D,5D,8D and 12D holders. Prepared hole (0.5xDC) is needed when using 8D/12D holder

Основной каталог Kyocera 2021 - 2022 - страница 696

Навигация

Spare parts

Recommended cutting conditions

General purpose GM / Cast iron KM

Counterboring FTP

Основной каталог Kyocera 2021 - 2022 - страница 696

Навигация

Spare parts

Recommended cutting conditions

General purpose GM / Cast iron KM

Counterboring FTP

Отправьте заявку

На подбор необходимой оснастки и оборудования