Основной каталог Kyocera 2021 - 2022

Каталог Kyocera пластины с CVD покрытием для обработки чугуна

Каталог Kyocera пластины TQ для нарезания резьбы c прессованным стружколомом

Каталог Kyocera высокопроизводительные модульные сверла DRA

Каталог Kyocera фрезы MRX с позитивными круглыми пластинами

Каталог Kyocera пластины с CVD покрытием для обработки стали

Points at bolt countersinking 1. Carbon steel Increase the feed rate to fz=0.1 ~ 0.15 (mm/t) for preventing long chips at low feed rates. Chip control is good when setting (Vc=80m/min) for MEF11~MEF25, and (Vc=120m/min) for MEF26~MEF48.

	Toolholder description	Vc(m/min)	fz(mm/t)
	MEF11~MEF25	80	0.1~0.15
	MEF26~MEF48	120	0.1~0.15
2. Sticky materials
Other applicationsOther applicationsStep feed is recommended for good chip control			T-Slot millT-Slot mill
Increase the feed rate to fz=0.1 ~ 0.15 (mm/t) for preventing long chips at low feed rate (fz=0.05mm/t).
Use cover to prevent accidents or injury by thick chips at higher feed rates.
	Toolholder description	Vc(m/min)	Step feed (mm) fz(mm/t)
	MEF11~MEF48	80~150	0.5~1.5 0.1~0.15
METS3. Stainless steel
Use a lower cutting speed. high cutting speeds cause chattering.

Cutting performance when shouldering	Description	Cutting range
MEF bolt countersink end mill is also recommended of shouldering.
	MEF11-S12	~

ae Vc=80~120m/min MEF14-S12

	DC	MEF17-S16	DC
S55C	-0.3-0.1		-0-0.1

CW -0.1-0.3 .3 CW-0.1-0.3

Dry	LU 0-0.2		MEF18-S16		LU 0-0.2
		LF					LF
	Fig. 1				Fig. 2
Overhang length:				DCX/6	DCX/3	DCX/2	Cutting width: ae(mm)

Same as LH in the dimension table MEF20-S16 Toolholder dimensions MEF22-S20

When shouldering, both side edge and bottom edges function.
Both edges wear at the same time depending on ap. The insert uses MEF25-S20

		Availa-							Dimensio	n (mm)			e	Spare	parts
		bility											t hol	Screw	Wrench(Torx)
D	escription	R	Inserts	Flutes	A.R.	R.R.	DC	DCON	LF	LU	CW	DN	Coolan Fig.			Applicable inserts
METS	21-S25	N	2	1			21	25	109	29	9	10.5	1	SB-2560TR	DT-8	SDMT060304E-K
	25-S25	N				-10	25		112	32	11	12.5	1
	32-S32	N	4	2	+9		32		120	38	14	15.5	No 1	SB-3060TR	DT-10	SDMT080308E-K
	40-S32	N				12	40	32	130	50	18	20.5	1	SB4085TR	DT15	SDMT120408EK
	50-S32	N				-	50		140	60	22	26.5	1	-	-	-
METS	21-S25-H	N	2	1			21	2	109	29	9	10.5	2	SB260TR	DT8	SDMT060304EK
	25-S25-H	N				-10	25	5	112	32	11	12.5	2	-5	-	-
	32-S32-H	N	4	2	+9		32		120	38	14	15.5	Yes 2	SB-3060TR	DT-10	SDMT080308E-K
	40-S32-H	N				12	40	32	130	50	18	20.5	2	SB4085TR	DT15	SDMT120408EK
	50-S32-H	N				-	50		140	60	22	26.5	2	-	-	-

M DCX/6 DCX/3 DCX/2 Cutting width: ae(mm)

METS...-H has air holes JIS standard of T-slot (Extracted from B0952) (Unit: mm)

A (Nominal size)	B	C	H Max.	Min.	A
12	19 +2 0	8 +1 0	25	20		H
14 18	23 +2 0 30 +2 0	9 +2 0 12 +2 0	28 36	23 30	B	C
22	37 +3 0	16 +2 0	45	38
28	46 +4 0	20 +2 0	56	48	Previous milling groo	ve does not affect.

Основной каталог Kyocera 2021 - 2022 - страница 986

Навигация

Основной каталог Kyocera 2021 - 2022 - страница 986

Навигация

Отправьте заявку

На подбор необходимой оснастки и оборудования