Grooving Internal dia.Internal dia.Internal dia. of the groove (MIN.)of the groove (MIN.)of the groove (MIN.) Ext. dia. of the groove øD1 CDX DMIN DMIN WF1DCON DAXN (min.) DAXX (max.) DCON Face grooving GVF type GIFV (Face grooving) CDX F DAXN LH H DAXN LF GFVSR... GFVSL... GIFVR3532B-201A GIFVL3532B-201A Right-hand shown Left-hand shown Right-hand Insert for Right-hand Toolholder, Left-hand Insert for Left-hand Toolholder. Toolholder dimensions Availabi-lity Dimension (mm) Spare partsClamp setWrench (Torx) Wrench (hex.) G Description Applicable inserts R L H LH LF WF GIFV& 3532B-201A N N 2.2 35 32 30 23 35(12) ∞ 250 16 CPS-5V - FT-15 - GVF&-... -...AGVF&-... -...AR GIFV& 3532B-351B3532B-352B5032B-501B5032B-502B N N 4.6 35NN5.1 35 50(25) (∞)32303025016 - CPS-6V -NN4.650N5.15070(25) (∞)GVF&250~350-020BGVF&-300-150BRGVF&400~490-020BLW-3GVF&-400-200BRGVF&250~350-020BGVF&-300-150BRGVF&400~490-020BGVF&-400-200BR GIFV& 5032B-501C5032B-502C NN NN 6.6 508.1 32 30 35 50 (25) 70 (∞) 250 16 - CPS-8V - GVF&350~450-040CLW-4GVF&500~600-040C CDX shows available grooving depth. Standard toolholders are designed with the edge position 1.0 mm above the center. The value ( ) of External dia. of the groove (MAX.) is the maximum outer diameter value after the initial groove between DAXN ~ DAXX (It is possible to widen the groove to infinity ∞). The value ( ) of Internal dia. of the groove (MIN.) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove between DAXN ~ DAXX. Applicable inserts reference page C42, G99, M216 External dia. of the groove depends on the application. Internal dia. of External dia. of the groove Applications Description the groove øD1 Remarks (MIN.) DAXN(min.)DAXX(max.) (MAX.) GIFV& 3532B-201A ∞ GIFV& 3532B-351B 35 50 3532B-352B External dia.of the groove 5032B-501B - ∞ - 5032B-502B 50 70 GIFV& 5032B-501C 5032B-502C GIFV& 3532B-201A 12 ∞ If øD1 ≥ 58-2CW, the Face Grooving Dia. can be expanded to GIFV& 3532B-351B 35 50 Internal dia. of the groove (MIN.) toward the Center. 3532B-352B CW = Edge Width 5032B-501B ∞ 255032B-502B If øD1 ≥ 75-2CW, the Face Grooving Dia. can be expanded to GIFV& 5032B-501C 50 70 Internal dia. of the groove (MIN.) toward the Center. 5032B-502C CW = Edge Width GIFV& 3532B-201A 12 ∞ GIFV& 3532B-351B 35 50 3532B-352B External dia.of the groove 5032B-501B 25 ∞ - 5032B-502B 50 70 GIFV& 5032B-501C 5032B-502C N : Standard item R : Right hand only L : Left hand only U : Check availability G106