Основной каталог Kyocera 2021 - 2022 - страница 873

Предыдущая страница Следующая страница

Навигация

Spare parts (MFSN88)

Clamp screwWrenchAnti-seize compoundMounting bolt
Description

MFSN 88050R-4T-M-G HH10X30

88063R-5T-M-G HH10X30 SB-4090TRP DTPM-15 88080R-6T-M-G HH12X35 P-37

88100R-7T-M-G Recommended tightening torque for insert clamp

88125R-9T-M-G3.5N•m-
88160R-11T-M-G
MFSN88050R-5T-M-GHH10X30
88063R-7T-M-GHH10X30
88080R-9T-M-GSB-4090TRPDTPM-15HH12X35
P-37
88100R-11T-M-GRecommended tightening torque for insert clamp

Lead angle 0°/ 2°Lead angle 0°/ 2°88125R-13T-M-G 3.5N•m -

88160R-15T-M-G MFLN90MFSN88 Coat anti-seize compound thinly on portion of taper and thread when insert is fixed.

Recommended cutting conditions

Coated carbide

eakerFeedRecommended insertgrades(Vc: m/min)
ipbrWorkpiece material(fz: mm/t)MEGACOAT(PVDCoated carbide)
ChPR1535PR1525PR1510PR015S
Carbon steel0.1~0.2~0.3✩ 120~180~250★ 120~180~250--
Alloy steel0.1~0.2~0.3✩ 100~160~220★ 100~160~220--
Mold steel0.1~0.15~0.25★ 80~140~180★ 80~140~180--
Stainless steel (Austenitic related)0.1~0.15~0.25✩ 100~150~200✩ 100~150~200--
GMStainless steel (Martensitic related)0.1~0.15~0.25✩ 100~150~200---
Stainless steel (Precipitation hardening)0.1~0.15~0.25★ 90~120~150---
Gray cast iron0.1~0.2~0.3--★ 120~180~250-
Nodular cast iron0.1~0.15~0.25--★ 100~150~200-
Ni-base heat-resistant alloys0.1~0.12~0.2✩ 20~30~50---
Carbon steel0.06~0.12~0.2-✩ 120~180~250--
Alloy steel0.06~0.12~0.2-✩ 100~160~220--
Mold steel0.06~0.08~0.15-✩ 80~140~180--
Stainless steel (Austenitic related)0.06~0.12~0.2★ 100~150~200✩ 100~150~200--
SMStainless steel (Martensitic related)0.06~0.12~0.2★ 100~150~200---
Stainless steel (Precipitation hardening)0.06~0.12~0.2✩ 90~120~150---
Gray cast iron0.06~0.12~0.2--✩ 120~180~250-
Nodular cast iron0.06~0.1~0.15--✩ 100~150~200-
Ni-base heat-resistant alloys0.06~0.08~0.15★ 20~30~50---
Titanium alloys0.06~0.08~0.15★ 40~60~80---
Carbon steel0.15~0.25~0.35-✩ 120~180~250--
Alloy steel0.15~0.25~0.35-✩ 100~160~220--
GHMold steel0.1~0.2~0.3-✩ 80~140~180--
Gray cast iron0.15~0.25~0.35--✩ 120~180~250-
Nodular cast iron0.1~0.2~0.3--✩ 100~150~200-
Hard materials (60HRC or less)0.1~0.2~0.3---★ 50~80~100
  • The bold-faced number indicates a center value of recommended cutting condition. ★: 1st Recommendation Adjust the cutting speed and the feed rate within the above conditions according to the actual machining situation. ✩: 2nd Recommendation
  • Machining with coolant is recommended for Ni-base heat-resistant alloys and titanium alloys.

Cermet Applicable chipbreaker range

Recommended insert gradesCoated carbideCermet
Feed(Vc: m/min)
ChipbreakerWorkpiece material(fz: mm/t)Cermet
55
TN620MGH
Carbon steel0.06~0.12~0.15★33
200~250~300SMGM
2GM
GMAlloy steel0.06~0.12~0.15★
180~220~250
0.50.5
Mold steel0.06~0.1~0.13★

150~180~220 0.06 0.1 0.2 0.25 0.3 0.35 0.06 0.1 0.15 0.2 0.3

★: 1st Recommendation fz (mm/t) fz (mm/t)

Applicable chipbreaker

Cutter type Fine pitch Extra fine pitch Not available for vertical milling (plunging).

Chipbreaker

GM SM GH

(Feed rate is recommended fz=0.2mm/t or under)

M101

Unmachined portion

Reference data of unmachined corner portion

ap1 mm2 mm3 mm4 mm5 mm
Unmachined portion0.82 mm0.93 mm0.97 mm1.00 mm1.04 mm