Основной каталог Kyocera 2021 - 2022 - страница 871

Предыдущая страница Следующая страница

Навигация

Lead angle 0°/ 2° MFSN88

MFSN88

DCSFMS DCSFMS DCB DCB KWW KWW

88°

DCCB2

DCCBDCCB 1
1
DCDC
DCXDCX
Fig. 1Fig. 2

DCSFMS DCB KWW DCCB3

88

88° DCCB4 PCD1 DCCB1 DC DCX Fig. 3

Toolholder dimensions

DescriptionAvaila- bility nserts A.R. R.R.Dimension (mm)Coolant hlWeight (k)Fig.
I RDCDCXDCSFMSDCBDCCB1DCCB2 DCCB3DCCB4 LFCBDPKDPKWWPCD1oeg
MFSN 88050R-4T-M-GN 4-125052482217.5114021631040.31
88063R-5T-M-GN 5-10636518..0.41
pitch 88080R-6T-M-G+1 N 60 -98082702720135024712.4N1.11
Fine 88100R-7T-M-GN 7-810010278324530814.4o1.42
88125R-9T-M-GN 9-7.5125127892.42
88160R-11T-M-GN 11-716016211040551463 2033916.466.74.23
MFSN 88050R-5T-M-GN 5-12505217.50.31
i tch 88063R-7T-M-GN 7-1063654822181140216.310.40.41
ine pi 88080R-9T-M-G1 N 90 -98082702720135024712.4N1.11
ra fi 88100R-11T-M-G+ N 11-810010278324530814.4o1.42
Ext i 88125R-13T-M-GN 13-7.5125127892.52
88160R-15T-M-GN 15-716016211040551463 2033916.4667433
PMX : 5 mm (GM, SM, GH Chipbre oat Anti-seize Compound thinly on i pare parts (MFSN88)akers, Coated cabid portion of taper a ie), 3 mm (GM nd thread wh i ClaChipbre en inser i mp screwaker, Ce t is fixedrmet) i.WrenchAnti-seizecompound. Mounting bolt.
Description
MFSN 88050R-4T-M-GHH10X30
88063R-5T-M-GHH10X30
pitch 88080R-6T-M-GSB-4090TRPDTPM-15P37HH12X35
Fine 88100R-7T-M-GRecommended tightening torque forinsert clamp
88125R-9T-M-G3.5N•m-
88160R-11T-M-G
MFSN 88050R-5T-M-GHH10X30
i ch 88063R-7T-M-GHH10X30
ie pit 88080R-9T-M-GSB-4090TRPDTPM-15HH12X35
tra fin 88100R-11T-M-GRecommended tightening torque forinsert clampP-37
Ex i 88125R-13T- 88160R-15T-M-G M-G3.5N•m-

Coat anti-seize compound thinly on portion of taper and thread when insert is fixed.

Recommended cutting conditions Recommended cutting conditions: M101

Coated carbide M99

Recommended insert grades ( Vc: m/min) Feed

Workpiece material (fz: mm/t) MEGACOAT (PVD Coated carbide)

PR1535PR1525PR1510PR015S
Carbon steel0.1~0.2~0.3✩★--
Alloy steel0.1~0.2~0.3✩★--
Mold steel0.1~0.15~0.25★★--
Stainless steel (Austenitic related)0.1~0.15~0.25✩✩--
GM Stainless steel (Martensitic related)0.1~0.15~0.25✩---
100~150~200
Stainless steel (Precipitation hardening)0.1~0.15~0.25★---
90~120~150
Gray cast iron0.1~0.2~0.3--★-
120~180~250
Nodular cast iron0.1~0.15~0.25--★-
100~150~200
Ni-base heat-resistant alloys0.1~0.12~0.2✩---
20~30~50
Carbon steel0.06~0.12~0.2-✩--
120~180~250
Alloy steel0.06~0.12~0.2-✩--
100~160~220
Mold steel0.06~0.08~0.15-✩--
80~140~180
Stainless steel (Austenitic related)0.06~0.12~0.2★✩--
Stainless steel (Martensitic related)0.06~0.12~0.2★---
SM100~150~200
Stainless steel (Precipitation hardening)0.06~0.12~0.2✩---
90~120~150
Gray cast iron0.06~0.12~0.2--✩-
120~180~250
Nodular cast iron0.06~0.1~0.15--✩-
100~150~200
Ni-base heat-resistant alloys0.06~0.08~0.15★---
20~30~50
Titanium alloys0.06~0.08~0.15★---
40~60~80
Carbon steel0.15~0.25~0.35-✩--
120~180~250
Alloy steel0.15~0.25~0.35-✩--
100~160~220
Mold steel0.1~0.2~0.3-✩--
GH80~140~180
Gray cast iron0.15~0.25~0.35--✩-
120~180~250
Nodular cast iron0.1~0.2~0.3--✩-
100~150~200
Hard materials (60HRC or less)0.1~0.2~0.3---★

50~80~100 * The bold-faced number indicates a center value of recommended cutting condition. ★: 1st Recommendation Adjust the cutting speed and the feed rate within the above conditions according to the actual machining situation. ✩: 2nd Recommendation