Основной каталог Kyocera 2021 - 2022 - страница 663

Предыдущая страница Следующая страница

Навигация

(6 Type, Pitch / TPI mm / TPIrtpro Descriptione) Corner-R (RE)Total ap (mm)No. of passes1234567891011(a 12 13p shows the va 14 15lue of rad 16ial ap) 17
0.75 mmTPGB1102005 11030050.050.4450.150.120.100.050.02
0.80 mmTPGB1102005 11030050.050.4750.150.140.100.060.02
1.00 mmTPGB1102005 11030050.050.6060.180.140.120.100.040.02
1.25 mmTPGB1102005 11030050.050.7670.180.160.140.120.100.040.02
150TPGB1102005 11030050.050.9280.200.180.160.140.100.080.040.02
. mm110201 1103010.100.8780.200.180.160.140.080.050.040.02
°) ead1.75 mmTPGB1102005 11030050.051.0990.200.180.160.140.130.120.100.040.02
c (60 l thr1103010.101.0490.200.180.160.130.120.100.080.050.02
Metri Interna2.00 mmTPGB1102005 11030050.051.25110.200.180.160.140.130.120.100.100.060.040.02
1103010.101.20110.200.180.160.130.130.120.100.080.050.030.02
2.50 mmTPGB1102005 11030050.051.57130.230.200.180.180.140.130.120.100.080.070.070.05 0.02
1103010.101.52130.230.200.180.180.130.130.120.100.080.070.050.03 0.02
TPGB1102005 11030050.051.90150.250.220.200.180.140.140.130.120.120.100.080.08 0.070.05 0.02
3.00 mm1103010.101.85150.250.220.200.180.140.140.130.120.100.100.080.07 0.050.05 0.02
1103020.201.75140.250.220.200.180.140.140.130.120.100.080.070.05 0.050.02
TPGB1102005 11030050.052.22160.250.220.200.180.180.160.160.140.140.120.120.10 0.100.08 0.050.02
3.50 mm1103010.102.17160.250.220.200.180.180.160.160.140.140.120.100.10 0.080.07 0.050.02
1103020.202.07150.250.220.200.180.180.160.160.140.140.120.100.08 0.070.05 0.02

110302 0.20 2.07 15 0.25 0.22 0.20 0.18 0.18 0.16 0.16 0.14 0.14 0.12 0.10 0.08 0.07 0.05 0.02 JJ

Guide for internal threading

For internal threading, pay extra attention to “stabilizing bore dia.” and “chip evacuation”.

1. “Stabilizing bore dia.”

Because small pitch Internal threading has small corner-R (RE), there is variation in the bore dia. Which may greatly influence the tool life of an insert. In order to eliminate the variation in the bore dia., “0” Cutting (zero cutting) should be performed as the zero pass, before the first pass in threading. The bore dia. Is cut with the specified dimension, and the first pass of threading becomes stable.

2. “Chip evacuation”

If machining process is continued when chips are tangled with a toolholder and other parts of the machine, it may cause damages to the insert. Therefore, please ensure that there are no tangled chips in the machine by the following method. <When processing the first workpiece> Set the program with the “single block” Keep the threading starting point 50 mm~100 mm away from the side of workpiece, and confirm that coolant is flushing down the chips for each pass. <When processing the second workpiece and later> Ensure that chips are not tangled; then, start the continuous run. 50mm~100mm