Основной каталог Kyocera 2021 - 2022 - страница 322

Предыдущая страница Следующая страница

Навигация

EZ adjust

Applicable sleeve structure

LF LF

L1

L1ONL2
ONDC
DC
LPRL3No.1 No.3LPRL3
No.1 No.3

No.2 No.4 H No.2 No.4 H

(Adjustment Pin Entry Point: Both Sides) (Adjustment Pin Entry Point: Both Sides)

(EZ Bar Installation Side) (EZ Bar Installation Side)

DCB DCB 2

Fig.3Fig.42
Sleeve dimensions
Bar overhang length*2 LPR (mm)
Avail-Dimensions (mm)
DescriptionAdjustment pin settingDrawingApplicable EZ Bar
ability
DCB DCONDCB2 HDD HLFL1L2*1 L3 No.1No.2No.3No.4
EZH 04516HP-10016151004–Fig.3
04519HP-12019.0518120
04520HP-12020191202318.5149.5EZB R/ …045…
4.56 1625.3L
04522HP-1352221135189(14)(9.5)(–)(–)Fig.4_045X…-050EZP
04525.0HP-1352524135
04525.4HP-12025.424.4120
EZH 05016HP-10016151004–Fig.3EZB R/L…050…
05019HP-12019.0518120EZBFR…050…
EZBTR…050…
05020HP-120201912025.520.515.510.5EZVBR…050…
56 1629
05022HP-1352221135189(15.5)(10.5)(–)(–)Fig.4EZG R/L…050…
EZFG R/L…050…
05025.0HP-1352524135EZTR…050…
05025.4HP-12025.424.4120_050X…-060EZP
EZH 06016HP-10016151004–Fig.3EZB R/ …060…
L
06019HP-12019.0518120EZBFR…060…
06020HP-120201912030.525.520.515.5EZVBR…060…
68 1631
06022HP-1352221135189(18.5)(13.5)(–)(–)Fig.4EZG R/L…060…
06025.0HP-1352524135EZTR…060…
06025.4HP-12025.424.4120_060X…-070EZP
EZH 07016HP-10016151004–Fig.3
EZB R/L…070…
07019HP-12019.0518120
35.530.525.520.5EZG R/L…070…
07020HP-1202019120
78 1633EZFG R/ …070…
07022HP-1352221135189(21.5)(16.5)(11.5)(–)Fig.4L
EZTR…070…
07025.0HP-1352524135
_070X…-080EZP
07025.4HP-12025.424.4120
EZH 08019HP-12019.0518120
08020HP-120201912040.535.530.525.5
EZB R/L…080…
08022HP-1358 228.4 16 2113518937Fig.4
(24.5)(19.5)(14.5)(–)_080X…-100EZP
08025.0HP-1352524135
08025.4HP-12025.424.4120

*1. L3 shows DCB length *2. LPR shows overhang length of the EZB Bar when attached to sleeve : Available ( ) value indicates the overhang length when installed the steel boring bar (EZ Bar PLUS). Choose sleeves (DCB) to meet with DCON dimension of bar Sleeve identification system EZ H 017 16 HP - 100

Bar symbol (EZ Bar)ApplicationShank dia.of EZ BarSleeve shank dia.Precision symbolOverall length of sleeve
H: Sleeve017: 1.7 mm025: 2.5 mm16: 16 Mm25.4: 25.4 MmCT: with coolant hole and EZ adjust structure100: 100 mm120: 120 mm
Hp: EZ adjust structure St: standard

EZ Bar mounting procedure (EZH-HP sleeve)

How to use adjustment pin (Fig. 5) Bar end (Slant) Adjustment pin

(1) Put the adjustment pin into the hole③Fig.5
3
(2) Push it into the sleeve, using the wrench "LW-1.5"How to use

②2 ①1 adjustment

(3) Tighten the clamp screw "HS3x4P" with wrench "LW-1.5" to fix the adjustment screw pin How to secure bar (Fig. 6) ①1 ②2

(1) With the chip pocket upward, set the bar in sleeve. Press the slant of the end of the Fig.6 bar against the adjustment pin. Make sure that the bar does not rotate (Fig.7) How to secure bar Chip pocket

(2) Tighten the clamp screw with wrench "LW-2" and secure the bar

(Use "LW-1.5" if shank dia. is 3 mm or less)

Fig. 7 Clamped bar