Основной каталог Kyocera 2021 - 2022 - страница 320

Предыдущая страница Следующая страница

Навигация

Parts (For EZH-CT sleeves)

Spare parts Clamp screw Clamp screw

Adjustment pin Wrench Wrench For EZ Bar adjustment

Description(for adjustment pin)(for Bar)
Wrench
Clamp screw LW-2
HS4x4
EZH017...CT-..HS3X4PLW-1.5LW-1.52
*For diameters under ø3, use
020...CT-..(for adjustmentLW-1.5 and HS3X4P (Same part

LCP025097 Tightening torque HS3X4P Tightening torque

025...CT-.. pin and liquid leak 1N • m of adjustment pin)

1N • m prevention) 030...CT-.. EZH 035...CT-..

EZ Bar

040...CT-.. HS3X4P

045...CT-..(for adjustmentLW-1.5LW-2Sleeve
LCP025097
050...CT-..pin and liquid leakHS4X4P

prevention) Tightening torque Tightening torque

060...CT-..1N • m(for bar)2N • mFor adjustment pin clamping and coolant
Adjustment pin hole
leak prevention
070...CT-..WrenchAdjustment pin
HS3X3PLW-1.5LCP025097
080...CT-..LCP025110(for adjustment pin and liquidLCP025110
leak prevention)1.5Clamp screw
HS3x4P

1) If shank dia. is ø2.5mm or less, 2) If shank dia. is ø3mm, Changeable overhang

HS3x3P length use clamp screw (HS3X4P) use clamp screw (HS3X4P) For adjustment pin.......................... 2 pcs For adjustment pin.......................... 2 pcs For liquid leak prevention ............ 2 pcs For liquid leak prevention ............ 4 pcs

For EZ Bar ............................................ 2 pcs For EZ Bar ............................................ 3 pcs

EZ Bar mounting procedure (EZH-CT sleeve)

How to use adjustment pin and prevent liquid leak (Fig. 4)

(1) Put the adjustment pin into the hole. Push it into the sleeve, using the wrench "LW-1.5"

(2) Tighten the clamp screw for the adjustment pin (HS3X4P, HS3X3P) using the wrench (LW-1.5) from the both sides of the sleeve (3) Put the clamp screws (HS3X4P, HS3X3P) into the holes for liquid leak prevention, using the wrench (LW-1.5) and fix them from the both sides of the sleeve

How to secure bar (Fig.5)

(1) With the chip pocket upward, set the bar in sleeve. Press the slant of the end of the bar against the adjustment pin

Make sure that the bar does not rotate (Fig.6)

(2) Tighten the clamp screw with wrench "LW-2" and secure the bar Adjustment pin

(Use "LW-1.5" if shank dia. is 3 mm or less)

Bar end (Slant)

Clamp screw

(For liquid leak prevention)

Clamp screw (For adjustment pin)

Chip pocket

Fig. 4 How to use adjustment pinFig. 5 How to secure barFig. 6 clamped bar
Sleeve identification system
EZ H 020 19 CT - 120

Bar symbol (EZ Bar) Application Shank dia. of EZ Bar Sleeve shank dia. Precision symbol Overall length of sleeve

H: Sleeve 020: 2.0 mm 025: 2.5 mm 19: 19.05 mm 25.4: 25.4 mm CT: With coolant 120: 120 mm 135: 135 mm

hole and EZ adjust structure HP: EZ adjust ST: Standard structure