Каталог Sumitomo токарные резцы (державки) для наружного точения - страница 31

Предыдущая страница Следующая страница

Навигация

93° 72.5˚

DVJN

General Turning & Profiling

− 93˚ LF

5˚ LH

117.5˚

DVJN / DVVN / DVQN

D General turning and profiling SEC- Type Tool Holders Double Clamp

  • Spare Parts
  • Wrench for shim is not included in the model body.
  • Holder This figure shows

Dimensions (mm) right handed tools. (for Torx hole)

Stock Height Width Total Cutting Cutting Head Applicable inserts

length edge edge height Clamp Screw Wrench Wrench for Wrench for

Cat. No. N m Shim

RLHBLF WF HF LHCat. No.Pagesetfor shimfor shim upper surface lower surface C
DVJN R/L2020K16● ●2020 125 252035From TRX10
  • VN 1604 SCP-4 5.0 VNS1604 BFTX0307N LH040 LH025
DVJN R/L2525M162525 150 322535B66(*)
Parts for Clamp SetC38

DVVN D General turning and profiling

SEC- Type Tool Holders Double Clamp General Turning

& Profiling 72.5˚ LF LH

  • Spare Parts
  • Wrench for shim is not included in the model body.
  • Holder

Dimensions (mm) (for Torx hole)

Height Width Total Cutting Cutting Head Applicable inserts Clamp Screw Wrench Wrench for Wrench for

Cat. No.Stocklengthedgeedge heightShimC
N m
HBLF WF HF LHCat. No. Pageset for shimfor shim upper surface lower surface
DVVN N2020K16●2020 125 10.0 2037From TRX10
●1604 VNVNS1604 BFTX0307N 5.0 SCP-4LH040 LH025
DVVN N2525M162525 150 12.5 2537B66(*)
C38 Parts for Clamp Set
D
DVQND General turning and profiling
Type SEC-
Tool Holders
117.5˚Double ClampR
General Turning,
Profiling & Necking −LF

10˚ LH

  • Spare Parts
  • Wrench for shim is not included in the model body.

S

  • Holder This figure shows
Dimensions (mm)right handed tools.(for Torx hole)
T

Stock Height Width Total Cutting Cutting Head Applicable inserts

length edge edge height Clamp Screw Wrench Wrench for Wrench for

Cat. No. N m Shim

RLHBLF WF HF LHCat. No.Pagesetfor shimfor shim upper surface lower surface
DVQN R/L2020K16● ●2020 125 252035From TRX10
  • VN 1604 SCP-4 5.0 VNS1604 BFTX0307N LH040 LH025
DVQN R/L2525M162525 150 322535B66(*)
V
Parts for Clamp SetC38
Applicable insertsDVJN / DVVN / DVQN

Type Type Type W

Name of chipbreaker / GU

1st Recommended Also see the insert selection guide (from page A8).CBN/PCD
●Depending on the size, there are some combinations that cannot be producedShape photography
Inserts
GradeAC8025P
or not available in order-to-made production.

Cutting range P (steel) M (stainless steel) K (cast iron) N (non-ferrous metal) H (hardened steel) Hard brittle material

Cutting stateFinishingMedium cuttingFinishingMedium cutting High-speed finishing Finishing–Medium cutting─CoatedNon-coatedFinishing
SUSUGUEFEGEGSUMIBORONSUMIBORON UZUZSUMIDIASUMIDIASUMIBORONSUMIBORON SUMIBORONSUMIBORON SUMIDIA BinderlessSUMIDIA Binderless
Continuous cut
T1500ZT1500ZAC810PAC810PAC6020MAC6020MAC6020MAC6020MBN7000/BNC500BN7000/BNC500AC405KAC405KDA1000DA1000BNC2010BNC2010BN1000BN1000BN1000BN1000
SUSUGUGUEFEFEGEGSUMIBORONSUMIBORON GZGZSUMIDIASUMIDIASUMIBORONSUMIBORON SUMIBORONSUMIBORON
Q
General cut
AC810PAC810PAC8025PAC8025PAC6030MAC6030MAC6030MAC6030MBN7000/BNC500BN7000/BNC500AC415KAC415KDA1000DA1000BNC2020BNC2020BN2000BN2000
SXSXUXEFEFEGEGSUMIBORONSUMIBORON GZGZSUMIDIASUMIDIASUMIBORONSUMIBORON SUMIBORONSUMIBORON
Q
AC8025PAC8025PAC830PAC830PAC6030MAC6030MAC6040MAC6040MBN7000/BNC500BN7000/BNC500AC420AC420KKDA1000DA1000BNC300BNC300BN350BN350

Recommended From A8 From A12 From A14 From A20 From A18 From M4