Каталог Sumitomo токарные резцы (державки) для наружного точения - страница 21

Предыдущая страница Следующая страница

Навигация

ESSN / ESKN

`■` Holder General Turning & Facing ESSNWF 45˚H LF LF2 HF –8˚ Fig1BFig2 Dimensions (mm) SEC-This figure shows right handed tools. Pi G 30Type Tool Holders`■` Spare n Lock eneral turiParts ng
Cat. No.Conventional Cat. No.Stock HeightW R L Hid Bth lTotal ength Total length 2 Cutting edge LF LF2 WFCutting edge height Fig HFApplicable inserts Cat. No. PageEccentric shaftShimWrench
ESSN R/L1212F09ESSN R/L1212`●` `●` 121280 73.8 1611.5 1SN 0903 B40P321US−
ESSN R/L1616H09ESSN R/L1616H32`●` `●` 1616100 93.8 2015.5 1P322US−
ESSN R/L1616H12ESSN R/L1616H431616100 91.7 2015.5 1P432U−
ESSN R/L2020K12ESSN R/L2020`●` `●` 2020125116.7 2519.5 1P433U−
ESSN R/L2020K12WESSN R/L2020W`●` `●` 2020125116.7 2519.5 2P433WESS42KY40
ESSN R/L2520M12ESSN R/L25202520150 141.7 2524.5 1SN 1204 From B41P434U−
ESSN R/L2520M12WESSN R/L2520W2520150 141.7 2524.5 2P434WESS42
ESSN R/L2525M12ESSN R/L25252525150 141.7 3224.5 1P434U−
ESSN R/L2525M12WESSN R/L2525W`●` `●` 2525150 141.7 3224.5 2P434WESS42

Note: When using a handed chipbreaker insert for facing, the holder and insert are oppositely handed.

ESKN 30 General turing

SEC- Type Fig2 Tool Holders Pin Lock C Facing

75˚

LF –5˚ Spare Parts –6˚ D Fig1 H HF

`■` HolderDimensions (mm)This figure right handeshows d tools.
Cat. No.Conventional Cat. No.StockHeightWidth Total length Cut edting geCutting edge heightFigApplicable insertsEccentricShimWrench
R LHBLFWFHFCat. No.Pageshaft
ESKN R/L1212F09ESKN R/L1212`●` `●`1212801611.51SN 0903B40P321US−
ESKN R/L1616H09ESKN R/L1616H32`●` `●`16161002015.51P322US−
ESKN R/L1616H12ESKN R/L1616H4316161002015.51P432U−
ESKN R/L2020K12ESKN R/L202020201252519.51P433U−
ESKN R/L2020K12WESKN R/L2020W`●` `●`20201252519.52P433WESS42KY40
ESKN R/L2520M12ESKN R/L252025201502524.51SN 1204From B41P434U−
ESKN R/L2520M12WESKN R/L2520W25201502524.52P434WESS42
ESKN R/L2525M12ESKN R/L252525251503224.51P434U−
ESKN R/L2525M12WESKN R/L2525W`●` `●`25251503224.52P434WESS42

V Note: When using a handed chipbreaker insert for facing, the holder and insert are oppositely handed.

Applicable inserts DSBN / DSDN / DSSN / PSSN / PSDN / PSBN / PSKN / ESBN / ESDN / ESKN / ESSN

Type Type Type Type Type Type Type Type Type Type Type

1st Recommended Also see the insert selection guide (from page A8). Name of chipbreaker / GU W

CBN/PCD

  • Depending on the size, there are some combinations that cannot be produced or not available in order-to-made production. Shape photography

Inserts Grade AC8025P

Cutting rangeP (steel)M (stainless steel)K (cast iron)H (hardened steel)Hard brittle material
Cutting stateFinishingMedium cutting Rough cuttingFinishingMedium cutting Rough cuttingHigh-speed finishing Finishing–Medium cutting Medium–Rough cuttingCoatedNon-coatedFinishing
SUSUGUMUMUEFEFEGEGEMEMSUMIBORONSUMIBORON UZUZGZGZSUMIBORONSUMIBORONSUMIBORONSUMIBORONSUMIDIA BinderlessSUMIDIA Binderless
Continuous cut
T1500ZT1500ZAC810PAC810PAC8025PAC8025PAC6020MAC6020MAC6020MAC6020MAC6030MAC6030MBN7000/BNC500BN7000/BNC500AC405KAC405KAC405KAC405KBNC2010BNC2010BN1000BN1000NPD10NPD10
SUSUGUGUMUMUEFEFEGEGEMEMSUMIBORONSUMIBORON GZGZGZGZSUMIBORONSUMIBORONSUMIBORONSUMIBORON
General cut–
AC810PAC810PAC8025PAC8025PAC8025PAC8025PAC6030MAC6030MAC6030MAC6030MAC6040MAC6040MBN7000/BNC500BN7000/BNC500AC415KAC415KAC415KAC415KBNC2020BNC2020BN2000BN2000
SXSXUXMXMXEFEFEGEGEMEMSUMIBORONSUMIBORON GZGZWithout breakerWithout breakerSUMIBORONSUMIBORONSUMIBORONSUMIBORON
Interrupted cut–
AC8025PAC8025PAC830PAC830PAC830PAC830PAC6030MAC6030MAC6040MAC6040MAC6040MAC6040MBN7000/BNC500BN7000/BNC500AC420KAC420KAC420KAC420KBNC300BNC300BN350BN350
Recommended From A8 From A12 From A14 From A18 From M4