Каталог Sumitomo токарные резцы (державки) для наружного точения - страница 30
Навигация
Каталог Sumitomo модульные фрезерные системы
Техническая информация Sumitomo
Каталог Sumitomo сверла и развертки
Каталог Sumitomo резьбонарезной инструмент
Каталог Sumitomo твердосплавные пластины
CTGP / CTAP / CTFP
Type Type Type 91˚
CTGP LH General turing
SEC- 40 Type Tool Holders General Turning Clamp-on
91˚ LF 5˚ Spare Parts
C
- This figure shows
Holder Dimensions (mm) right handed tools.
Conventional Cat. Stock Height Width Total Cutting Cutting Head Offset Applicable inserts Insert Shim Wrenches
| Cat. No. | length edge | edge height | Clamp | Bolt | Shim | Spring | ||
| Chipbreaker | for upper |
| No. | R L | H | B LF WF HF LH WF2 | Cat. No. | Page | retainer | |||||
| Piece | surface | ||||||||||
| CTGP R/L1919-L16 | FP22 R/L-33 | ● | 19 19 140 25 19 34.5 6 TP | 1603 | B116 DCR/L2 CBD4R/L BH0824R/L STPD322 | LH040 |
- SPP3 DSP5
CTGP R/L2525-N22 FP22 R/L-44B 25 25 160 32 25 41.0 7 TP 2204 B117 DCR/L3 CBD5R/L BH1030R/L STPD422 LH050
CTAP 40 General turing
SEC- Type Tool Holders Clamp-on General Turning 91˚
LF 5˚
- Spare Parts
C
- This figure shows
Holder Dimensions (mm) right handed tools.
D Conventional Cat. Stock Height Width Total Cutting Cutting Head Applicable inserts Insert Shim Wrenches
| Cat. No. | length | edge | edge height | Clamp | Bolt | Shim | Spring | ||
| Chipbreaker | for upper |
| No. | R L | H | B | LF WF HF LH | Cat. No. | Page | retainer | ||
| Piece | surface |
CTAP R/L2525-N16 FP21 R/L-44A 25 25 160 25 25 34.5 DCR/L2 CBD4R/L BH0830R/L STPD322 LH040
TP 1603 B116
| CTAP R/L3225-N16 | FP21 R/L-45A | 32 | 25 160 25 | 32 34.5 | DCR/L2 CBD4R/L BH0830R/L STPD322 | SPP3 DSP5 | LH040 | ||
| R | |||||||||
| CTAP R/L3232-Q22 | FP21 R/L-55 | 32 | 32 180 32 | 32 41.0 TP | 2204 B117 DCR/L3 CBD5R/L BH1036R/L STPD422 | LH050 |
S CTFP General turing
HBKL SEC- 40 Type Tool Holders Facing Clamp-on 91˚
T LF Spare Parts V
- This figure shows
Holder Dimensions (mm) right handed tools.
Stock Height Width Total Cutting Cutting Head Offset Level Applicable inserts Insert Shim Wrenches
W Conventional Cat. length edge edge height difference
Cat. No. Clamp Chipbreaker Bolt Shim Spring for upper
| No. | R L | H | B | LF WF HF HBKL WF2 HBKW Cat. No. Page | retainer | ||
| Piece | surface |
| CTFP R/L1919-L16 | FP25 R/L-33 | ● 19 19 140 25 19 26 | 6 | 8 | BH0824L/R | |||
| CTFP R/L2525-N16 | FP25 R/L-44A ● | 25 25 160 32 25 26 | 7 | − | TP | 1603 B116 DCL/R2 CBD4L/R BH0830L/R STPD322 | LH040 | |
| CTFP R/L3225-N16 | FP25 R/L-45A | 32 25 160 32 32 26 | 7 | − | BH0830L/R | SPP3 DSP5 | ||
| CTFP R/L2525-N22 | FP25 R/L-44B ● | 25 25 160 32 25 33 | 7 | 7 | BH1030L/R | |||
| TP | 2204 B117 DCL/R3 CBD5L/R | STPD422 LH040 | ||||||
| CTFP R/L3232-Q22 | FP25 R/L-55 | 32 32 180 39 32 33 | 7 | − | BH1036L/R |
Note: When using a handed chipbreaker insert for facing, the holder and insert are oppositely handed.