Общий каталог Mitsubishi 2020 - 2021 - страница 906

Предыдущая страница Следующая страница

Навигация

SQUAREBALLRADIUSTAPERBARRELROUGHINGSOLID END MILLS CARBIDE y Slotting Carbon steel (─30HRC) Alloy steel, Pre-hardened steel Austenitic stainless steel, Titanium alloy Work Material AISI 1035, AISI 1050, ASTM 283 AISI H13, AISI 4140, AISI P21 AISI 304, AISI 306, AISI 316L, Ti-6Al-4V etc. High speed General purpose Depth of High speed General purpose Depth of High speed General purpose Depth of DC cutting cutting cut cutting cutting cut cutting cutting cut (inch) Revolution Table feed Revolution Table feed ap Revolution Table feed Revolution Table feed ap Revolution Table feed Revolution Table feed ap (min-1) (IPM) (min-1) (IPM) (inch) (min-1) (IPM) (min-1) (IPM) (inch) (min-1) (IPM) (min-1) (IPM) (inch) 1/8 15000 59.1 10000 26.0 .13 12000 30.2 8000 13.4 .13 10000 26.8 6000 10.6 .13 3/16 10000 75.6 6700 33.5 .19 8000 35.9 5300 15.7 .19 6700 28.5 4000 11.4 .19 1/4 7500 74.4 5000 32.7 .25 6000 39.7 4000 17.3 .25 5000 29.1 3000 11.4 .25 5/16 6000 66.1 4000 29.1 .31 4800 37.8 3200 16.5 .31 4000 31.5 2400 12.6 .31 3/8 5000 61.4 3300 26.8 .38 4000 34.0 2700 15.0 .38 3300 33.8 2000 13.4 .38 1/2 3800 47.9 2500 20.9 .50 3000 29.8 2000 13.0 .50 2500 31.5 1500 12.6 .50 DC Depthof cut ap DC : Dia. Precipitation hardening martensitic stainless steel, Copper, Copper alloy Heat resistant alloy Work Co-Cr-Mo alloy Material ASTM S 17400, ASTM S 17700, Inconel718 etc. 17-4PH, 15-5PH etc. High speed General purpose Depth of High speed General purpose Depth of High speed General purpose Depth of DC cutting cutting cut cutting cutting cut cutting cutting cut (inch) Revolution Table feed Revolution Table feed ap Revolution Table feed Revolution Table feed ap Revolution Table feed Revolution Table feed ap (min-1) (IPM) (min-1) (IPM) (inch) (min-1) (IPM) (min-1) (IPM) (inch) (min-1) (IPM) (min-1) (IPM) (inch) I 1/8 6000 15.1 5000 8.3 .063 18000 70.9 12000 31.1 .13 3000 6.14 2500 3.4 .038 3/16 4000 18.3 3300 9.8 .094 12000 90.7 8000 39.4 .19 2000 6.80 1700 3.8 .056 1/4 3000 19.8 2500 11.0 .13 9000 89.3 6000 39.4 .25 1500 7.09 1300 3.9 .075 5/16 2400 18.9 2000 10.2 .16 7200 79.4 4800 35.0 .31 1200 7.56 1000 4.3 .094 3/8 2000 17.0 1700 9.4 .19 6000 73.7 4000 32.3 .38 1000 8.19 840 4.7 .11 1/2 1500 14.9 1300 8.7 .25 4500 56.7 3000 24.8 .50 750 7.56 630 4.3 .15 DC Depthof cut ap DC : Dia. Note 1) SMART MIRACLE coating has reduced electric conductivity; therefore an external contact type (electric transmitted) tool setter may not work. When measuring the tool length, please use an internal contact type (non-electricity type) tool setter or a laser type tool setter. Note 2) Effective cutting of stainless steel, titanium alloy and heat-resistant alloy can be achieved with the use of water-soluble cutting fluid. Note 3) Higher feeds and speeds can be used for smaller depth of cut. Note 4) Vibration can still occur if the machine rigidity and clamping method are insufficient. In these cases the feed and speed should be reduced proportionately. I147